Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Brady Co. Automatic Indentification Products CG Triumvirate is a trademark of Agfa Corporation. Corrupad is a Trademark of Corrupad Protective Packaging Inc. Bradyprinter THT Model 1024 is a Trademark of Brady USA Inc. As an Energy Star Partner, Brady USA Inc. has determined that this product meets the Energy Star guidelines for energy efficiency. Information in this document is subject to change without notice and does not represent a commitment on the part of Brady USA Inc. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser's personal use, without the expressed written permission of Brady USA Inc. All rights reserved. Printed in the United States of America. © Copyright 1997 by Brady USA Inc. 6555 W. Good Hope Road · Milwaukee, Wisconsin · 53223 800-537-8791 Customer Support 800-643-8766 Technical Support Part Number: 88-2184-01 Revision: C Agency Compliance and Approvals: FCC: This device complies with Part 15 of FCC rules. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Important Safety Instuctions Your Bar Code Printer has been designed to give you many years of safe, reliable service. As with all electrical equipment, there are a few basic precautions you should take to avoid getting hurt or damaging the Printer. • Carefully read the installation and operating instructions provided with your Printer. • Read and follow all warning instruction labels on the Printer itself. • Place the Printer on a flat, firm, solid surface. • To protect your Printer from overheating, make sure all openings on the Printer are not blocked. • Do not place the Printer on or near a heat source, (i.e., a radiator or heat register). • Do not use your Printer near water, or spill liquid of any kind into it. • Be certain that your power source matches the rating listed on the bottom of the Printer. If you are unsure, check with your dealer or with your local power company. • Do not place the power cord where it will be walked on. If the power cord becomes damaged or frayed replace it immediately. • Do not insert anything into the ventilation slots or openings on the Printer. • Only qualified, trained service technicians should attempt to repair your Printer. ¤ .. Contents ¤ .. Getting Started 1.0 Introduction ...............................................................1 1.1 Unpacking and Inspection...........................................1 1.2 Printer Specifications .................................................2 1.3 Connecting Power ......................................................4 1.4 Switches and Indicators..............................................5 1.5 Interfacing to the Printer.............................................6 1.6 Loading Media...........................................................7 1.7 Loading Media for Peel Configuration ........................8 1.8 Loading Ribbon (Thermal Transfer) ..........................9 1.9 Adjusting for Wide to Narrow Media........................11 1.10 Power-up Configuration and Self-Test......................12 1.11 Available Options ....................................................13 ¤ .. Printing Labels 2.0 Introduction .............................................................15 2.1 Programming Commands .........................................16 2.2 Programming Examples ...........................................21 2.3 Configuration Command String ................................22 2.4 Printing Bar Codes...................................................23 2.5 Memory Cartridges (Modules)..................................24 ¤ .. Maintenance 3.0 Introduction .............................................................25 3.1 Cleaning the Printhead..............................................25 3.2 Media Width Adjustment..........................................26 3.3 Fine Printhead Adjustment........................................27 3.4 Printhead Replacement .............................................28 (continued) i Appendix A ASCII Control Code Chart ..............................................A-1 Appendix B Available Fonts and Bar Codes........................................B-1 Appendix C Error Codes.....................................................................C-1 Appendix D Warranty Information..................................................