Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Принтеры - DocuPrint 96 MX (26.9 kb)
Принтеры - DocuPrint 96 MX (28.4 kb)
Принтеры - DocuPrint 96 MX (604.08 kb)
Принтеры - DocuPrint 96 MX (27.41 kb)
Фрагмент инструкции
• The System Controller must be positioned within the line-of-sight of the printer for safety purposes while servicing the equipment. • Customer must supply a table or desk for the HCU and System Controller. Work surface must be at least 36” X 36” to provide enough space for the components and cables, as well as for service access. • For proper operation, the printer component must be perfectly level. On floors less than two degrees out of level, a leveling kit must be used to level the equipment. The printer will not function properly on floors more than two degrees out of level. For additional space/ configuration options, refer to the Xerox DocuPrint 96/4635/ 180 NPS/IPS Installation Planning Guide (Pub #721P8XXXX) . System connections • Ethernet LAN running TCP/ IP, AppleTalk, or Novell NetWare network protocol software. • Token Ring running TCP/IP or AppleTalk network protocol software • Bus and tag channel connection, using the Host Channel Unit ( HCU) or the PCI board and control unit • For the DocuPrint 180 NPS/ IPS only: Fibre Distributed Data Interface (FDDI) running TCP/IP, Novell 3. x, or AppleTalk network protocols ( available only with the Solaris 2.x environment). The FDDI supports a Single Connection configuration only. Note: DocuPrint does not support multiple network interfaces simultaneously. Special considerations • Transference of the black toner to poly- vinyl surfaces is a common occurrence. • Print quality is guaranteed to a range of three to four millimeters for edge marking and six millimeters for text printing to the edge of the page. • Xerox carbonless paper is approved for DocuPrint 96/4635/ 180 NPS/IPS only. Refer to the Xerox Supplies Catalog for the reorder numbers. • Appearance of very small spots is a common occurrence on all xerographic printers. Consult your Xerox service representative for details on acceptable spot occurrence specifications. Environmental requirements Recommended Minimum Maximum Operating temperature 72o +/ - 4o F 22o +/ - 2o C 50o F 85o F Humidity 45% +/ - 10% RH 30% RH 65% RH Normal Maximum Altitude Up to 6,000 feet above sea level 9,000 feet above sea level Heat dissipation Standby Running Printer Module 4,454 BTU/Hr (Fuser on) 2,700 BTU/ Hr (Energy Saver) 96/4635 NPS/ IPS: 28,140 BTU/Hr 180 NPS/IPS: 32,770 BTU/Hr System Controller 1,100 BTU/Hr Electrical requirements HCU or PCI board & control unit System Controller Printer Module 96/4635/180 NPS/IPS 50 Hz Voltage 100-240 VAC +/- 10% 100-240 VAC +/- 10% WYE (star) (3 phase, 5 wire) 380, 400, 415 VAC Current 15 amp 15 amp WYE (star) (3 phase, 5 wire) : 20 amp ( power connection per local codes/ regulations) 96/4635/180 NPS/IPS 60 Hz Cord # 1 Cord # 2 (180 NPS/ IPS only) Voltage 120/240 VAC (Located within 6 ft. 120 VAC (1 phase) 2 dedicated outlets are required 120/ 208 VAC; or 120/ 240 VAC (2 phase) 120/208 VAC; or 120/240 VAC ( 2 phase) Current 15 amp 15 amp 50 amp 30 amp Receptacle NEMA Part No. Standard wall outl...
Эта инструкция также подходит к моделям:Принтеры - DocuPrint 96 (42.44 kb)
Принтеры - DocuPrint 180 (4180) (42.44 kb)
Принтеры - DocuPrint 180MX (42.44 kb)
Принтеры - DocuPrint 4635 (42.44 kb)