Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
When the printer is used as a kitchen printer, please use this port for kitchen bell connection instead. Power Connection The power connector is a 3-PIN jack between the peripheral connector and the parallel connector for PP-8000. Either a Posiflex supplied power adaptor or a printer power cable from a Posiflex POS system can be connected to this connector to supply power for this printer. During insertion of the power plug, be sure to hear the click to obtain a firm contact. CAUTION: Before doing the insertion or extraction of the power plug, be sure to pull the outer sleeve of the plug backward to release the internal latch. Failure to do this could damage the power plug. Such damage is considered as an artificial destruction and is not covered by the warranty. Power On When all the above cable connections are made correctly, you may connect your power adaptor to the wall outlet. Make sure that the type of power cord and the voltage requirement of the power adaptor meet the local power conditions. Now the printer is ready for power on. Self Test Press and hold down the feed button while turning the on / off switch on. The printer will then perform a self-test. A sample slip of self-test result is printed as in the sample at right. Please note that both serial and parallel interfaces are indicated. That means the printer is working on an auto-sensing and auto-select algorithm. The header is printed in text mode and the rest part of this slip is printed in page mode. If FEED button is pressed at this moment, a font table will be printed in text mode again. To exit the test printing, please turn the printer off and on again. Part 8 SPECIAL ADJUSTMENTS Paper Near End Sensor The near end sensor for paper roll in the printer is able to have the printer work with paper rolls of several bobbin sizes. Please refer to the picture at right for the inside of the paper roll compartment that there are a plastic thumb wheel for bobbin size adjustment and a sensor block in the wall. Turn the thumb wheel to adjust the proper position of sensor block. For desktop application, the sensor block should be above the bobbin seating on the 2 support rollers on bottom of paper compartment when paper near end. The acceptable paper roll bobbin outer diameter is between 18 and 24 mm. 58mm Paper Spacing Plate Sensor Block Sensor Position Adjust Support Roller Paper Roll Shaft Hold A B C A B C 58 mm Compartment The application of 58 mm width paper roll in this printer can be achieved through adoption of an option spacing plate and an internal DIP switch setting. Please refer to the last chapter of this manual for the DIP switch setting. Please refer to the middle picture above for the 58 mm paper spacing plate with its flange at top edge showing out. Insert the noted corners of the spacing plate into the 3 dents inside the paper roll compartment as arrowed in the left picture above with point A goes in first. Then the 58 mm paper roll sub compartment is formed as in the right picture above. Paper Cutting The paper advance after a normal cut with auto paper feed is set to 12 mm. In case the user applies cut without paper feed through DIP switch setting change to have something like a logo printed on top of each slip, it is also highly suggested to print the logo and necessary paper feeding to make 12 mm paper advance right after each cut to prevent curling up and jamming of paper Part 9 front edge inside the paper exit slot. INSTALLING DRIVER There will always be a Posiflex Product Information CD or DVD or a separate CD of similar nature but specifically created for the product delivered. Please find the appropriate subfolder from the non-specific Posiflex Product Information CD or DVD and check the information file like “readme” or installation guide or application guide and follow the instructions inside. LAN PRINTER SPECIFIC ISSUES Web Manager The default static IP for the PP-8000L is 192.168.192.168 and default listen port is 9100. User may set his own IP to the same network segment and use any browser to connect to the printer IP to configure the LAN setup of the PP-8000L including changing the printer IP for application according to his network administrator’s request. However, DHCP is not supported. Reset Pin Hole As the LAN setup for the PP-8000L can be set freely, if the changes are not well registered some troubles could be introduced. Therefore, in PP8000L, there is a “Reset pin hole” near the LAN connector. Use something like a ball pen tip or straightened end of paper clip to push and hold for at least 5 seconds into this hole will reset the LAN setup of the printer back to the default values at delivery so the user may re-do all setup. The LAN setup can be viewed in second paragraph of self-test printout for the PP-8000L. LAN POS Printer Manager This utility can be used to manage multiple PP-8000L’s connected in same network under Windows as long as there is no conflicting IP in the network. This utility can assign to eac...
Эта инструкция также подходит к моделям:Принтеры - AURA PP-8000L (798.57 kb)
Принтеры - AURA PP-8000U (798.57 kb)