Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
or other equivalent Core : O12 mm (inner diameter), O18 mm (outer diameter) [Caution] Do not paste the paper to the core. 2.3.2 Printing Position 2.3.3 Head and Cutter Positional Relations CITIZEN 9 CBM-230/231 User’s Manual 3 APPEARANCE AND COMPONENT PARTS CITIZEN 10 CBM-230/231 User’s Manual 4 OPERATION 4.1 Connecting the Interface Cable 1. Turn off the power. 2. Confirm the vertical direction of a cable terminal and connect it to the interface connector. 3. Fix the cable terminal. Serial interface : Tighten screws to fix. Parallel interface : Turn a fixture in an arrow direction to fix. 4. Connect the cable to the computer. CITIZEN 11 CBM-230/231 User’s Manual 4.2 Connecting the Drawer Kick Connector 1. Turn off the power. 2. Confirm the vertical direction of a drawer kick cable connector and insert it into the drawer kick connector on the back of the printer. 3. Using a screw, fix a drawer's earthing conductor to the earth terminal of the printer. [Caution] Connect only a specified drawer(solenoid) to the drawer kick connector. CITIZEN 12 CBM-230/231 User’s Manual 4.3 Inserting the Paper Roll [Caution] Be sure to use a specified paper roll. 1. Open the printer cover. 2. Shift the head-up lever in an arrow direction to move up the printing head. [Caution] When setting the paper roll, you do not have to open the auto cutter. (CBM-231) CBM-231 CITIZEN 13 CBM-230/231 User’s Manual 3. Using the scissors, cut the end of the paper at a right angle. [Caution] Do not insert the paper with its end fluffed or bent. 4. Confirm the winding direction of the paper roll. Opening the paper holder in the direction of the arrow, set the paper and hold the core center properly. [Caution] Make sure that the paper roll rotates smoothly without tilting the paper. CITIZEN 14 CBM-230/231 User’s Manual 5. Insert the end of the paper into the paper inlet, turn the paper feed knob in the direction of the arrow to feed out the paper about 5 cm from the paper outlet of the auto cutter or nose of the manual cutter. (The figure below shows the CBM-231). [Caution] Do not turn the paper feed knob when the printing head is in its down position. 6. When the paper is tilting, correct it and move the printing head down. CITIZEN 15 CBM-230/231 User’s Manual 7. Cut off the surplus paper at the edge of the paper outlet of the auto cutter or blade of the manual cutter. 8. Close the printer cover. You are finished with setting of the paper roll. [Caution] Do not open the printer cover during printing. 9. When removing the remaining paper upon its replacement with new one, pull it out straight with the printing head kept up. 10. When using the auto loading function, follow the procedure below. (1) Change the setting of the DIP switch to the auto loading mode. (Turn on DS1-3) (2) Move the printing head up. (3) Insert the end of the paper straight into the paper inlet of the printer and move down the printing head. The paper is automatically pulled in by a constant amount. (4) Close the printer cover to finish setting of the paper roll. [Caution] When the paper is tilting, move up the printing head and correct it manually. CITIZEN 16 CBM-230/231 User’s Manual 4.4 Operation Panel 1. POWER LED(green) Illuminated when the power is supplied. 2. ERROR LED(red) Indicates different errors, depending on the illuminated or blinking condition. ERROR DETAIL DISPLAY PATTERN RESETTING METHOD Printer cover open Illuminated Close the cover Head Up Illuminated Move down the head Memory check Disabled Head overheat Automatically reset by temperature drop Macro execution wait Press the LF switch Cutter motor lock Eliminate paper jam and press LF switch 3 PAPER LED(red) Near end enabled : Illuminated when the paper is near its end (Stops after printing the set length) Near end disabled : Illuminated when the paper is at its end (Stops printing) [Caution] Use the DIP switch to enable or disable the near end detecting function. 4 LF switch Pressing this switch for a short time feeds the paper by one line. Holding it down feeds the paper continuously. In case of macro execution wait, pressing the LF switch executes it. [Caution] Depending on a selection of the DIP switch, the paper can be fed when the cover is opened. CITIZEN 17 CBM-230/231 User’s Manual 5 LF switch and power switch Self-printing is performed by turning on the power switch with the LF switch held down. 4.5 Opening the Auto Cutter(CBM-231) When the paper is jamming or when you open the auto cutter in order to clean the head, raise the auto cutter, pulling the cutter lock lever in the direction of the arrow. [Caution] Immediately after printing, the printing head and motor have a high temperature. Never touch the printing head and motor when you open the auto cutter. CITIZEN 18 CBM-230/231 User’s Manual 5 SETTING OF DIP SWITCHES The DIP switches are located in the position shown in the figure below. Unscrew and remove the DIP switch cover. [Caution] Turn off the power to set the DIP switch. CITIZEN 19 CBM...