Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Принтеры - HL-5170DN (2.43 mb)
Принтеры - HL-5170DN (2.59 mb)
Фрагмент инструкции
Figure 1-20 ABOUT THIS PRINTER 1 - 18 Make sure that the paper is straight and in the proper position in the manual feed tray. If it is not, the paper may not be fed properly, resulting in a skewed printout or a paper jam. ¦ Do not put more than one piece of paper in the manual feed tray at the same time, or it may cause a jam. ¦ If you put any Media (paper, transparency and so on) in the manual feed tray before the printer is in the Ready state, the media may be ejected without being printed on. 6 After the printed page comes out of the printer, put in the next sheet of paper as in Step 5 above. Repeat for each page that you want to print. 7 Close the face-up output tray. Caution Remove each sheet immediately after printing. Stacking the sheets may cause a paper jam or the paper to curl. Figure 1-21 1 - 19 ABOUT THIS PRINTER Printing on thicker paper and card stock from the multi-purpose tray (MP tray) (For HL-5150D and HL-5170DN) 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Thick paper or Thicker paper Paper Source: MP Tray Printing on thicker paper and card stock from the multi-purpose tray (MP tray) (For HL-5150D and HL-5170DN) 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Thick paper or Thicker paper Paper Source: MP Tray PS driver ABOUT THIS PRINTER 1 - 20 2 Open the face-up output tray, and then pull out the face-up output tray support if necessary. 2 Open the face-up output tray, and then pull out the face-up output tray support if necessary. Figure 1-22 3 Open the MP tray and lower it gently. Figure 1-23 4 Pull out the MP tray support flap. MP tray support flap Figure 1-24 1 - 21 ABOUT THIS PRINTER 5 When putting paper in the MP tray, make sure it touches the back of the tray and remains under the maximum paper height guides on both sides of the tray. 5 When putting paper in the MP tray, make sure it touches the back of the tray and remains under the maximum paper height guides on both sides of the tray. Figure 1-25 Make sure that the paper is straight and in the proper position in the MP tray. If it is not, the paper may not be fed properly, resulting in a skewed printout or a paper jam. 6 While pressing the paper-guide release lever, slide the paper guide to fit the paper size. Figure 1-26 When you put paper in the MP tray, please remember the following; ¦ During printing, the inside tray rises to feed paper into the printer. ¦ The side to be printed on must be face up. ¦ Put the leading edge (top of the paper) in first and push it gently into the tray. ¦ The top of the paper stack must be under the maximum paper height guides that are on both sides of the tray. 7 Send the print data to the printer. 8 Close the face-up output tray. ABOUT THIS PRINTER 1 - 22 Remove each sheet immediately after printing. Stacking the sheets may cause a paper jam or the paper to curl. Figure 1-27 1 - 23 ABOUT THIS PRINTER Printing on envelopes Types of envelopes to avoid Do not use envelopes: ¦ that are damaged, curled, wrinkled, or an usual shape ¦ that are extremely shiny or textured ¦ with clasps, snaps or tie strings ¦ with self-adhesive closures ¦ that are of a baggy construction ¦ that are not sharply creased ¦ that are embossed (have raised writing on them) ¦ that were previously printed by a laser printer ¦ that are pre-printed on the inside ¦ that cannot be arranged when put in a pile ¦ that are made of paper that weighs more than the paper weight specifications for the printer ¦ that have been badly made, with edges that are not straight or consistently square or ¦ with windows, holes, cutouts or perforations Figure 1-28 IF YOU USE ANY OF THE TYPES OF ENVELOPES LISTED ABOVE, THEY MAY DAMAGE YOUR PRINTER. THIS DAMAGE IS NOT COVERED UNDER ANY BROTHER WARRANTY OR SERVICE AGREEMENT. ¦ Before you print envelopes, you must ‘fan’ the stack to avoid paper jams and misfeeds. ¦ Do not put different types of paper in the paper tray at the same time because it may cause paper jams or misfeeds. ¦ Do not print envelopes using duplex printing. ¦ For proper printing, you must choose the same paper size from your software application as the paper in the tray. ¦ See What kind of paper can I use? on page 1-5. Most envelopes will be suitable for your printer. However, some envelopes will have feed and print-quality problems because of the way they have been made. A suitable envelope should have edges with straight, well-creased folds and the leading edge should not be thicker than two pieces of paper. The envelope should lie flat and not be of baggy or flimsy construction. You should buy quality envelopes from a supplier who understands that you will be using the envelopes in a laser printer. Before you print a lot of envelopes, test one to make sure that the print results are what you want. Brother will not recommend a particular envelope because envelope manufacturers may change the envelope specifications....
Эта инструкция также подходит к моделям:Принтеры - HL-5150D (2.48 mb)
Принтеры - HL-5140 (2.48 mb)