Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
To get your machine ready for use, please follow the instructions in this Set-Up Sheet before referring to any other documentation. READ THIS SHEET FIRSTREAD THIS SHEET FIRST • DO NOT assemble the machine or connect the USB cable before installing the software. You will be instructed when to assemble and connect the cable. IMPORTANT . Machine . Multi-purpose tray . Tray cover ..Printhead . Paper output tray . Ink tanks (Black, cyan, magenta, yellow) . Power cord . Documentation (Set-Up Sheet, Quick Reference Guide) . MultiPASS MP730/700 Setup CD-ROM NOTE •A printer cable is not included. You must purchase a USB cable (less than 16 # / 8 ft./5 m) to connect your machine to a computer. NOTE •When installing the software in Windows 2000/XP, you must log on as Administrator or have Administrator privileges. •If you have previously installed an earlier version of the MultiPASS Suite software (version 4.4 or earlier), you must uninstall it before installing this version. For details on uninstalling the software, refer to the documentation of the previous version. Install the software. 1 Turn on your computer. 2 On your computer, quit any open applications, including virus checkers. 3 Insert the MultiPASS MP730/700 Setup CD-ROM into your disk drive. 4 In the [MP Setup] screen, click [Install MP Drivers]. • If Set-up screen is not displayed, on the Windows desktop,double-click [My Computer] (Windows XP:Click [Start], then click [My Computer]). Open the CD-ROM icon, then double-click [setup (setup.exe)]. 5 Follow the on-screen instructions. If you need to restart your computer, If you do not need to restart your computer, the following screen is displayed. the following screen is displayed. Make sure [Yes, I want to restart my computer now.] is selected and then click [Finish] to restart your computer. (Do not remove the CD-ROM at this stage.) 6 Click [Finish]. 7 In the [MP Setup] screen, click [Install MP Toolbox]. • If you had to restart your computer and Set-up screen is not displayed or you have closed it, on the Windows desktop,double-click [My Computer] (Windows XP:Click [Start], then click [My Computer]). Open the CD-ROM icon, then double-click [setup (setup.exe)]. 8 Follow the on-screen instructions. 9 Click [Finish]. IMPORTANT • Proceed to step below to assemble the machine. Please keep your computer powered on. Remove the shipping material from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. Assemble the machine. 1 Attach the multi-purpose tray. 2 Attach the paper output tray listen for audible click. Connect the power cord. IMPORTANT • Before turning on the power, make sure the document cover Ais closed. Load paper. Place a stack of paper (print-side up) in the multi-purpose tray q. Pinch the paper guide Aand adjust to the width of the stack w. Then place the tray cover Dover the multi-purpose tray e. NOTE •Make sure the stack does not exceed the paper limit mark Bor tab C. Otherwise a paper jam may occur. C q e w A D B PLEASE WAIT PUT IN CARTRIDGE Approx. 30 seconds 1 Plug the power cord into a socket. 2 When you connect the machine, the Alarm light blinks, and the messages above should appear in the LCD. 3 If nothing appears in the LCD, press [ON/OFF (1 sec.)] to turn on the machine. • If you need to turn off the machine, press [ON/OFF (1 sec.)] for one second. ON/OFF(1sec.) A Turn over to continue Install the printhead. 1 Press [Open] qand lift up the scanning unit w. IMPORTANT • Do not touch the metal rod or any parts inside the machine. • The machine must be turned on when opening the scanning unit. 2 Remove the printhead from its packaging, then remove the orange protective cap A. IMPORTANT • Do not touch the electrical contacts B. 3 Raise the lock lever C, then gently slide the printhead into the holder. Lower the lock lever. IMPORTANT • Do not lift the lock lever once the printhead has been installed. C B A q w Install the ink tanks. 1 Start with the yellow ink tank. Pull the orange tape in the direction of the arrow and remove the plastic wrapper so you can see the air hole A. Turn the ink tank over so that the protective cap Bis facing up.Then hold the ink tank as shown below and remove the protective cap B. NOTE • To avoid spilling ink, never press on the long sides of the ink tank C. • Once you remove the protective cap B, do not touch the ink port D. 2 Insert the ink tank (label-side up) into the correct slot (refer to the color guide on the printhead). Press down gently on the ink tank until an audible click is heard. 3 Repeat steps 1 and 2 to install the remaining magenta, cyan, and black ink tanks. IMPORTANT • Make sure the ink tanks are inserted all the way into their slots. 4 Close the scanning unit until it locks into place. Align the printhead as explained in step 9. Align the printhead. NOTE • You can also align the printhead from the software. For details, refer to the Software Guide. 1 When the LCD Adisplays the follo...