Оценок - 5, средний балл: 4.2
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Copyright ©2002 CANON INC. All rights reserved. No part of this publication may be transmitted or copied in any form whatsoever without the express written permission. Setting Up 1 Preparing the Printer 1 1111 Place the printer on a flat surface. 2 2222 Remove the tape and the shipping material from the printer as shown. The tape position is subject to change. 2 Connecting the Printer to the Computer Use either a USB cable or parallel printer cable. You cannot connect the computer to the printer using both the parallel cable AND the USB cable. USB cable • Windows XP, Windows Me, Windows 2000, Windows 98, • Mac OS 8.6 or later Recommended: Canon or other computer manufacturer cable, up to 5 meters in length. Printer cable (parallel) • Windows NT 4.0, Windows 95 (Can also be used with Windows XP, Windows Me, Windows 2000 and Windows 98.) Should conform with Centronics IEEE 1284 and support bi-directional communication. Recommended: Canon or other computer manufacturer cable, up to 2 meters in length. . • The USB cable delivers relatively faster printing speeds and is recommended for use with Windows XP, Windows Me, Windows 2000 and Windows 98. • If your computer has an earth connection, make sure that this is attached. • If you do not intend to use the printer for a long period of time, unplug the power cord from the power outlet after turning off the printer. Follow the steps below to install the printer drivercorrectly. 1 1111Ensure the printer and the computer are switched off. Figure A 2 2222Connect the cable. Figure A shows the USB cable connection and Figure B shows the printer cable (parallel) connection. Figure B If the Add New Hardware Wizard or Found New Hardware Wizard screen appears when carrying out the following operations, click Cancel and turn off the computer. 3 Installing the Print Head • Never attempt to plug the power cord into the power outlet or unplug the power cord when your hands are wet. • Never damage, modify, stretch, or excessively bend or twist the power cord. Do not place heavy objects on the power cord. • Never use any power supply other than the standard power supply available in the country of purchase. Using the incorrect voltage and frequency could cause a fire or electric shock. • Always push the plug all the way into the power outlet. • ........Installing the Print Head ON 1 1111 Plug the printer in. 2 2222Turn on the printer. Do NOT turn on the computer yet. The POWER lamp flashes and the printer begins to operate. Wait until the POWER lamp remains fully lit. 3 3333 Open the front cover. 4 4444 Remove the tape. 5 5555Raise the lock lever. Do not touch internal parts other than the lock lever. 5 6 Remove the protective cap from the print head. 7 Place the print head in the holder. 8 Lock the print head into place by lowering the lever. Do not touch the lock lever once the print head has been installed. ........ Installing the Ink Tanks • For safety reasons, store ink tanks out of the reach of small children. 1 Take out the yellow ink tank. 2 Pull the orange tape in the direction of the arrow and remove the clear film. • Do not touch the print head nozzles or electrical contacts. • Do not attempt to reattach the protective cap once it has been removed. print head nozzles electrical contacts print head print head holder 3 3333Hold the ink tank as shown in the protective cap diagram and remove the protective cap. ink port • Do not squeeze the sides of the ink tanks as this may cause the ink to leak out and stain your clothes and hands. • Do not touch the ink port. • Do not attempt to reattach the protective cap once it has been removed. 4 4444Insert the yellow ink tank into the right- hand slot. Press the top until it clicksinto place. 5 5555Use the same procedure to install the other ink tanks in their appropriate slots. Check the labels to make sure that each tank is in the correct position. • Only install the ink tanks in the positions specified by the labels. • If ink tanks are not installed in the right position, colors will not be printed correctly. Immediately reinstall the tank in the correct position and carry out print head cleaning. For details, refer to the Black Cyan Magenta Yellow User’s Guide. 6 6666Close the front cover. Wait until the POWER lamp remains fully lit (about 60 seconds). 4 Loading Paper • ........Loading A4 (Letter) Size Plain Paper paper thickness lever 1 1111 Open the front cover. 2 2222 Move the paper thickness lever at the top of the print head holder to the leftposition. Close the front cover. Set the paper thickness lever to the left when using plain paper, to the right when using thick paper. Refer to the User’s Guide for information on loading envelopes and other media. 3 3333 Pull out the paper rest and the outputtray as shown. print side 4 4444Load the paper, aligning it with the rightside of the sheet feeder. You can load up to 100 sheets of plain paper. Do not exceed this limit. 5 5555Press the paper guide and slide itagainst the left...