Оценок - 2, средний балл: 3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Rear Output Slot (Face up) Control Panel Functions 1 Use to store frequently-dialed fax number and dial them with a touch of the buttons. Adjusts the brightness of the documents for the current copy job. 2 C O P Y Selects the document type for the current copy job. Makes a copy smaller or larger than the original document. Selects the number of copies. 3 Displays the current status and prompts during an operation. Scrolls through the options available for the selected menu item. 4 Confirms the selection on the display. Enters Menu mode and scrolls through the menus available. 1.6 GETTING STARTED 1 1 4 Sends you back to the upper menu level. Stops an operation at any time. In Standby mode, clears/cancels the copy options, such as the darkness, the document type setting, the copy size and the number of copies. Starts a job. 5 Dials a number or enters alphanumeric characters. 6 S A V E Allows you to save on toner by using less toner to print a document. Allows you to save on call costs by sending a fax at a preset toll-saving time. Using this feature, you can take advantage of lower long distance rates at night, for example. Allows you to select the fax receiving mode. • Allows you to store frequently-dialed fax numbers using a one or two-digit speed dial or group number for automatic dialing and edit the stored numbers. • Allows you to print a Phone book list. 7 F A X Adjusts the resolution of the documents for the current fax job. Allows you to send a fax to multiple destinations. Engages the telephone line. Redials the last number in Standby mode or inserts a pause into a fax number in Edit mode. GETTING STARTED 1.7 1.8 GETTING STARTED Attaching Accessories Document Output Support Insert the two tabs on the supplied document output support into the slots on both sides of the paper output tray. Fold out the extender, if necessary. NOTES: • When you want to use the paper output extension, first slightly lift the document output support up, then fold out the extension. • When detaching the document output tray, detach it by pressing the front portion of document output tray as seen from the picture. As this time, even though the dull sound is heard the components are safe from damge. GETTING STARTED 1.9 1 Handset and Handset Cradle 1 Plug the end of the coiled cord of the handset into the jack on the left side of your machine. 2 Holding the cradle as shown, attach the handset cradle to the machine. . Insert the two tabs of the cradle into the slots on the left side of the machine as shown. . Push the cradle toward the machine until it locks into place. NOTES: • The cradle and handset must be installed for correct operation of the set. • To remove the cradle, push it down, pressing the latch on the bottom of the cradle. Installing the Toner Cartridge 1 Open the front cover. 2 Remove the starter toner cartridge from its bag. Gently roll the cartridge 5 or 6 times to distribute the toner evenly inside the cartridge. Thoroughly rolling the cartridge will assure the maximum copies per cartridge. CAUTIONS: • To prevent damage, do not expose the toner cartridge to light for more than a few minutes. Cover it with a piece of paper, if left exposed for more than a few minutes. • If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into the fabric. 1.10 GETTING STARTED GETTING STARTED 1.11 1 3 Slide the toner cartridge into the machine until it locks into place completely. 4 Close the front cover. Make sure that the cover is securely closed. Loading Paper You can load approximately 250 sheets. To load a stack of Letter-sized paper: 1 Pull open the paper tray and remove it from the machine. 2 Push down on the pressure plate until it locks into place. 3 Fan the edges of the paper stack to separate the pages. Then tap the stack on a flat surface to even it up. 1.12 GETTING STARTED GETTING STARTED 1.13 1 4 Insert the paper stack into the paper tray with the side you want to print on facing up. NOTE: If you want to load a different size of paper, you need to adjust the paper guides. For details, see page 1.14. 5 Pay attention to the paper limit mark on the left inside wall of the tray. Paper overloading may cause paper jams. 6 Insert and slide the paper tray back into the machine. NOTE: After you load the paper, you need to set up your machine for the paper type and size you loaded. See page 1.36 for copying and faxing, or page 3.7 for PC-printing. 1.14 GETTING STARTED Changing the Paper Size in the Paper Tray To load longer sizes of paper, such as Legal-sized paper, you need to adjust the paper guides to extend the paper tray. 1 After pressing and unlatching the guide lock, slide the paper length guide out completely to extend the paper tray to its full length. 2 After inserting paper into the tray, slide in the guide until it lightly touches the end of the paper stack. For paper smaller than letter, adjust the paper length guide accordingly. 3 Pinching the paper ...
Эта инструкция также подходит к моделям:Принтеры - CF-565PR (6.53 mb)
Принтеры - SF-565P (6.53 mb)
Принтеры - SF-565PRC (6.53 mb)
Принтеры - Mono Multifunction Printer SF-565P Series (6.53 mb)