Оценок - 0, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
An error has occurred in the firmware program of the printer. The job automatically clears and the printer returns to Standby Mode. • Expand the memory in your printer. See “Installing Printer Memory” on page F.2. Paper Empty The paper tray has run Load paper in the paper tray. See [Size] In Tray1 out of papers. page 3.4. Paper Empty [Size] In Tray2 Paper Empty [Size] In Mp Paper Empty [Size] In Manual Page Too Complex Too much complicated data was sent to the printer. Simplify the page layout and remove any unnecessary graphics from your document. To expand the memory in your printer, see “Installing Printer Memory” on page F.2. Ready [Color] Low Toner The corresponding toner cartridge in your printer is nearly empty. Redistribute the toner in corresponding toner cartridge, referring to page 6.5. Ready An IP address conflicts Contact your network IP Conflict with only other devices on the network. administrator and choose an address within your subnet which will not conflict with any other devices. 7.28 SOLVING PROBLEMS Replace [Color] Toner Message The corresponding toner cartridge in your printer is empty. Status Replace the corresponding toner cartridge with a new one. See page 6.8. Do this... Replace Fuser The lifetime of the fuser is done. Contact a service representative. Replace Fuser Soon The lifetime of the fuser is nearly done. When “Replace Fuser” appears on the display, replace the fuser. Replace Imaging Unit The lifetime of the imaging unit is done. Replace the imaging unit with a new one. See page 6.14. Replace Imaging Unit Soon The lifetime of the imaging unit is nearly done. When “Replace Imaging Unit” appears on the display, replace the imaging unit. Replace MP Roller The lifetime of the MP pickup roller is done. Contact a service representative. Replace Transfer Belt The lifetime of the transfer belt is done. Replace the transfer belt with a new one. See page 6.22. Replace Transfer Belt Soon The lifetime of the transfer belt is nearly done. When “Replace Transfer Belt” appears on the display, replace the transfer belt. Replace Transfer Roller The lifetime of the Transfer Roller is done. Contact a service representative. Replace Transfer Roller Soon The lifetime of the Transfer Roller is nearly done. When “Replace Transfer Roller” appears on the display, contact a service representative. Replace Tray1 Roller The lifetime of the Tray1 pickup roller is done. Contact a service representative. Replace Tray2 Roller The lifetime of the Tray2 pickup roller is done. Contact a service representative. Transfer Belt Error The transfer belt is either not working or not correctly installed in the printer. Replace the transfer belt. OR Make sure the installed transfer belt is properly seated. Tray2 Error Optional Tray2 is not properly installed or connected to the printer. After turning the printer off and then back on, reinstall the optional tray2. If the message persists, contact a service representative. 7 SOLVING PROBLEMS 7.29 Tray2 Jam Cover Open Message Tray2 jam cover is open. Status Close Tray2 cover firmly. Do this... Waste Motor Error A problem has occurred in waste toner motor. Contact a service representative. Waste Toner Tank Full/Not Install The waste toner container is full. Replace the waste toner container with a new one. See page 6.11. Common Windows Problems Problem “File in Use” message appears during installation. Possible Cause and Solution Exit all software applications. Remove all software from the StartUp Group, then restart Windows. Reinstall the printer driver. “Error Writing to LPTx” • Ensure that the cables are connected correctly and that message appears. the printer is on. • If bi-directional communication is not turned on in the driver, it will also cause this message. “General Protection Fault”, Close all other applications, reboot Windows and try “Exception OE”, “Spool32”, printing again. or “Illegal Operation” messages appear. “Fail To Print”, “A printer This message may appear during printing. Just keep timeout error occurred.” waiting until it finishes printing. If the message appears in message appear. standby mode or after printing is completed, check the connection and/or whether an error occurred. NOTE: Refer to the Microsoft Windows 9x/Me/NT 4.0/2000/XP User’s Guide that came with your PC for further information on Windows error messages. 7.30 SOLVING PROBLEMS Common Macintosh Problems Common Macintosh Problems Problems in the Chooser 7 Problem Possible Cause and Solution The printer driver icon does not appear in Chooser. The printer name does not appear in the Select a PostScript Printer box in the Chooser. • Make sure that the cables are connected correctly and the printer is turned on. • Check if “Ready” appears on the display of the control panel. If not, press the On Line/Continue button to switch your printer to on-line. • Make sure that the correct printer driver has been selected in Chooser. • If the printer resides on a network with multiple zones, mak...
Эта инструкция также подходит к моделям:Принтеры - CLP-550 (10.09 mb)
Принтеры - CLP-550G (10.09 mb)