Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
9. Raise the top cover (A). This is done by inserting the side pins of the top cover into the slots in the upper cabinet. A 6.Place the paper with the printed side face down and align the paper sprocket holes (B) with the tractor pins (C), then close the tractor cover (A). A 10. Raise the paper support (A). ABC 7. A Adjust the tractors (A) to remove any slack. B Lock the tractor clamping levers (B). A BBAABBAAAB Note • Make sure the paper is straight. Operating Instructions Setup Setup Insert the paper support into the slot of the extension plate (A) until it stops. A 12. If the ON LINE indicator is not lit, press to get ready to print. ON LINE Single Sheets and Envelopes (Friction Mode) 1. A Turn the power on. The PAPER OUT indicator will flash indicating that no paper is installed in the printer. B Adjust the head gap lever for the thickness of paper you are using. PositionUsed for1 or 2Thinner sheets3, 4, 5 and 6Thick sheets or envelopes ABHEAD GAP A 2. Set the paper feed selector (A) to the " " position. Operating Instructions Setup Setup . This is done by inserting the side pins of the top cover into the slots in the upper cabinet. A 4. Raise the paper support (A). A Note •lf the extension plate is already installed (Page 22), it does not need to be removed. 5. A Separate the paper guides to the approximate width of your paper or envelope. Note • To predetermine your left most print position, move the left paper guide until it clicks into place. B Insert a sheet of paper through the paper guides (A). The paper will be automatically loaded to the first print line. BAA Note • You can disable Auto load through the Control Panel Software program (Page 25) or by using the Control Panel (Page 33). • If Auto load is disabled, you must press to load paper. LOAD/PARK • If you need to align the paper horizontally or vertically, set the paper feed selector to " ". This releases the paper and allows the paper to be positioned manually as required. Set the selector back to " " before printing. 6. If the ON LINE indicator is not lit, press ON LINE to get ready to print. Operating Instructions Setup Setup With fanfold paper installed, this function allows you to advance your paper to the tear position. After tearing off the page you can return your paper to the first printer line by pressing TEAR OFF again. If TEAR OFF is not pressed a second time, the printer will automatically reverse to the first print line upon receiving data from the computer. 1. Press TEAR OFF to advance the paper to the tear position. 2. Tear off the page. 3. Press TEAR OFF to reverse the paper back to the first print line. Self Test The printer has a self test feature which allows you to test the printer. When activated, this feature will print 5 lines of each resident font. When complete, it will return to the draft font and continue for approximately 20 minutes. 1. Install the ribbon cassette and paper, then turn the power off (Page 18–24). 2. While pressing LF/FF turn the power on, then release. A sample printout will begin, which serves as a self test. 3.Once you see that the printer is functioning properly, you may turn the power off during the self test, or you may run the entire test. Operating Instructions Using the Software Using the Software This software is used to change the configuration of the printer. Using this software, you can also print out the printer's character table. It is necessary to install the printer driver to use this software. When using the Windows driver, these settings are rarely used. When using the Windows driver, make sure Emulation is set to "EPSON". The printer is compatible with most popular software packages. If no changes are required, you should be ready to print. In most cases there will be no need to change the initial setup items. To start the Control Panel Software program, from [Start], select [All programs] ® [Panasonic] ® [Panasonic KX-P1131E] ® [Control Panel Software]. You can change the following items: Print Style Font Draft, Bold PS, Courier, OCR-B, Prestige, Roman, Sans Serif, Script, Bold PS-SC, Courier-SC, Prestige-SC, Roman-SC, Sans Serif-SC, Script-SC Note • "-SC" sequences are displayed only when one of the following Code pages is selected: USA, Multilingual, Portugal, Canada-French, Norway, Turkey. Pitch 10 CPI, 12 CPI, 15 CPI, 17 CPI, 20 CPI, P.S, 5 CPI, 6 CPI, 7.5 CPI, 8.5 CPI Point size 8, 10, 10.5, 12, 14, 16, 18, 20, 21, 22, 24, 26, 28, 30, 32 Note • Displayed only when an "-SC" sequence is selected in Font. Emulation Emulation EPSON (Epson LQ-300 without color) IBM (IBM Proprinter X24E) Page Format Line/in. 1, 1.5, 2, 2.5, 3, 4, 4.5, 5, 6, 7.5, 8, 9, 10, 12, Scalable Page length 11 in., 12 in., 14 in., 11 2/3 in., 8 in., 8 1/2 in., 5 1/2 in., Free Top margin 0–450 (1/180 in.) Bottom margin 0–900 (1/180 in.) Left margin 10 CPI or 5 CPI pitch: 0–78 characters 12 CPI or 6 CPI pitch: 0–93 characters 15 CPI or 7.5 CPI pitch: 0–117 characters 17 CPI or 8.5 CPI pitch: 0–133 character...