Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Handling Paper Your Panasonic printer offers two paper feed choices: – Fanfold paper (Tractor push mode) – Single sheets and envelopes (Friction mode) Fanfold Paper (Tractor Push Mode) 1. A Turn the power on. The PAPER OUT indicator will flash indicating that no paper is installed in the printer. B Adjust the head gap lever (A) for the thickness of paper you are using. PositionUsed for1 or 2Thinner sheets3, 4, 5 and 6Thick or multiple sheets 123456ABA A Operating Instructions Setup Setup . A Unlock the tractors by pulling the tractor clamping levers (A) forward. 2. Set the paper feed selector (A) to the " " position. B Slide the tractors (B) to accommodate the approximate width of paper being used. A 3. Lift off the top cover (A). ABBABA 5. Raise the tractor covers (A). A A Operating Instructions Setup . Setup . 6. Place the paper with the printed side face down 8. Press and align the paper sprocket holes with the This will load the paper to the first print line. tractor pins, then close the tractor covers. Make sure the paper is straight. 7. A Adjust the tractors to remove any slack. B Lock the tractor clamping levers. 9. Replace the top cover. 10. If the ON LINE indicator ( ON LINEA) is not lit, press to get ready to print. ABAB A Operating Instructions Setup Setup 1. A Turn the power on. The PAPER OUT indicator will flash indicating that no paper is installed in the printer. B Adjust the head gap lever (A) for the thickness of paper you are using. PositionUsed for1 or 2Thinner sheets3, 4, 5 and 6Thick sheets or envelopes 123456ABA A 2. Set the paper feed selector (A) to the " " position. 3. Raise the top cover (A) to single sheet feed position. This is done by inserting the side pins of the top cover into the slots in the upper cabinet. A 4. Raise the paper support (A). A 5.Insert a sheet of paper with the printed side face down behind the platen by aligning its left edge 0 with on the top cover. Operating Instructions Setup Setup s LOAD/PARK. Self Test The paper will be loaded to the first print line. The printer has a self test feature which allows you to test the printer. 1. Load a sheet of paper, and turn the power off. (Page 20) 2. Turn the power on while pressing LF/FF. 7. If the ON LINE indicator ( ON LINEA) is not lit, press to get ready to print. A sample printout will begin, which serves as a self test. 3.Turn the power off. A Operating Instructions Using the Software Using the Software This software is used to change the configuration of the printer. Using this software, you can also print out the printer's character table. It is necessary to install the printer driver to use this software. When using the Windows driver, these settings are rarely used. When using the Windows driver, make sure Emulation is set to "EPSON". The printer is compatible with most popular software packages. If no changes are required, you should be ready to print. In most cases there will be no need to change the initial setup items. To start the Control Panel Software program, from [Start], select [All programs] ® [Panasonic] ® [Panasonic KX-P1121E] ® [Control Panel Software]. You can change the following items: Emulation EPSON (Epson LQ-850) IBM (IBM Proprinter X24E) Character set Italic (Epson only) Graphic 1 Graphic 2 Code page USA (PC-437) Multilingual (PC-850) Portugal (PC-860) Canada-French (PC-863) Norway (PC-865) Turkey (PC-857) International character USA, France, Germany, UK, Denmark1, Sweden, Italy, Spain1, Japan, Norway, Denmark2, Spain2, Latin America, Korea, Legal Font Draft, Courier, Prestige, Bold PS Pitch 10 CPI, 12 CPI, 15 CPI, 17 CPI, 20 CPI, P.S Zero font Normal (0) Slashed ( 0) Page length 11 Inch, 12 Inch, 14 Inch, 11 2/3 Inch, 8 Inch, 8 1/2 Inch, 5 1/2 Inch Auto LF On (CR+LF) Off (CR only) Auto CR (IBM only) On (LF, VT, ESC+"J" +CR) Off (LF, VT, ESC+"J" only) Skip perforation On (1 inch skip) Off (No skip) A.G.M (Alternate Graphic Mode) (IBM only) On, Off Graphic direction Uni Direction, Bi Direction Download buffer Enable, Disable Auto load On (Available) Off (Not available) Auto Online On (Available) Off (Not available) TOF set (# / 72 inch) Tractor: 0–360 Friction: 0–360 Note • The following items can also be set through the Control Panel (Page 27): Emulation, Page length, Auto LF, Graphic direction and Download buffer Operating Instructions Using the Software Using the Software Sends the settings to the printer. Restore Default Returns the settings to default. After pressing this button, the screen to select your country is displayed. Select your country. If your country is not displayed here, select [Other country]. Character Table Prints out the character table of the built-in font in the printer. After pressing this button, the screen to select the emulation and character table is displayed. Select the desired table. About Displays the version of the software. Exit Exits the software. Note • The screen to select your country is only displayed when activating the software for the first ti...