Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
2) Close the printhead. CALIBRATING PLEASE WAIT The printer automatically adjusts the scale (gain) of the signals it receives from the media and ribbon sensors based on the specific media and ribbon combination you are using. On the sensor profile, this essentially corresponds to moving the graph up or down to optimize the readings for your application. ---RELOAD ALL When .RELOAD ALL” is displayed: 1) Open the printhead and pull the media forward until a label is positioned under the media sensor. 2) Move the ribbon back to its proper position. 3) Close the printhead. MEDIA AND RIBBON CALIBRATE Now that the scale has changed, the printer performs a calibration equivalent to pressing the CALIBRATE key. During this process, the printer checks the readings for the media and ribbon based on the new scale you have established, determines the label length, and determines whether you are in direct thermal or thermal transfer print mode. The process is now complete! To see the new readings on the new scale, print a sensor profile. Brady X-PLUS Series User.s Guide Setting Communication Parameters Communication parameters must be set correctly for the printer to communicate with the host. These parameters make sure that the printer and host are .speaking the same language.” All communications parameters are password protected. Press Display Shows Action/Explanation PARALLEL COMM Setting Parallel Communications Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: Parallel Selections: Parallel, twinax/coax Select the communications port that matches the one being used by the host computer. SERIAL COMM Setting Serial Communications Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: RS232 Selections: RS232, RS422/485, RS485 multidrop Select the communications port that matches the one being used by the host computer. BAUD Setting Baud Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: 9600 Selections: 110, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600 The baud setting of the printer must match the baud setting of the host for accurate communications to take place. Select the value that matches the one being used by the host. DATA BITS Setting Data Bits Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: 7-bits Selections: 7-bits, 8-bits The data bits of the printer must match the data bits of the host for accurate communications to take place. Set the data bits to match the setting being used by the host. NOTE: Must be set to 8 data bits to use Code Page 850. Brady X-PLUS Series User.s Guide Press Display Shows Action/Explanation PARITY Setting Parity Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: Even Selections: Even, odd, none The parity of the printer must match the parity of the host for accurate communications to take place. Select the parity that matches the one being used by the host. STOP BITS Setting Stop Bits Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: 1 stop bit Selections: 1 stop bit, 2 stop bits The stop bits of the printer must match the stop bits of the host for accurate communications to take place. Select the stop bits that match the one being used by the host. HOST HANDSHAKE Setting Host Handshake Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: XON/XOFF Selections: XON/XOFF, DTR/DSR The handshake protocol of the printer must match the handshake protocol of the host for communications to take place. Select the handshake protocol that matches the one being used by the host. PROTOCOL Setting Protocol Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: None Selections: None, Zebra, ACK/NACK Protocol is a type of error checking system. Depending on the selection, an indicator may be sent from the printer to the host signifying that data has been received. Select the protocol that is requested by the host. Further details on protocol can be found in the ZPL II Programming Guide Volume I. NOTE: Zebra is the same as ACK/NACK except that with Zebra the response messages are sequenced. NOTE: If Zebra is selected, printer must use .DTR/DSR” host handshake protocol. Brady X-PLUS Series User.s Guide Press Display Shows Action/Explanation NETWORK ID Setting Network ID Press the LEFT BLACK OVAL key to move to the next digit position, press the RIGHT BLACK OVAL key to increase the value of the digit. Default: 000 Range: 000 -999 Network ID is used to assign a unique number to a printer used in an RS-422/RS-485 network. This gives the host the means to address a specific printer. If the printer is used in a network, you must select a network ID number. This does not affect TCP/IP or IPX networks. COMMUNICATIONS Setting Communications Mode Press the RIGHT or LEFT BLACK OVAL key to display other choices. Default: Normal mode Selections: Normal mode, diagnostics The communication diagnostics mode is a troubles...
Эта инструкция также подходит к моделям:Принтеры - 203X-PLUS (1.26 mb)
Принтеры - 300X-PLUS (1.26 mb)
Принтеры - and 360X-PLUS (1.26 mb)