Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
If this does not correct the condition, power the printer off, and then back on before calling for service. OFF Normal status Keys: Reset Initializes the printer. Use the Reset key after loading supplies, to end Power Saving, or after an error occurs. Menu Press MENU to access the printer settings. Continue to press the MENU key to access the settings in the order listed in “Using the Printer LCD panel” on page 36. Enter Confirms the user selection. Arrow Keys Use the up and down arrow keys to select options within a menu selection. Exit Exits the current menu or menu selection and returns user to the previous menu selection. LCD Display Line one of the display shows the current printer or mode status. The > symbol following a menu selection indicates that there are subcategories listed within the selection. Use the up and down arrow keys to select these options. RP90 Plus E and RL90 User Guide Using the LCD menus Press the MENU key and "User Mode" is displayed on the LCD panel. The LCD panel changes to read "Display" within 0.5 seconds. Press the ENTER key when "Display" is shown to access display settings which include the card counter, LCD contrast, and LCD background color. Press the MENU key when “Ready” is displayed to access other printer settings. Press the EXIT key at any time to exit the menu system and return to "Ready" status. Speaker Provides an electronic beep that indicates: • An error has happened. • Fewer than 20 cards remain in the card hopper. • Confirms that settings have been saved. The speaker function can be turned on or off using the LCD panel. Using the Printer LCD panel Many printer settings can be changed using the Status Monitor. See “Status Monitor” on page 25. Menu Display Settings Function Display Counter • Total • Head •Free Contrast 0 Back Color SKY BLUE Counter Reset OK? Cleaning Rollers OK? Magnetic Stripe (MG) Head Use the up and down arrow keys to select the card counter type: • Total is the default setting, and displays the number of cards printed. The Total counter cannot be reset. • Head displays the number of complete dye panels. The Head counter cannot be reset, however, it automatically resets itself when the print head is replaced. • The Free counter displays the number of cards that have printed. The Free counter can be reset by the user. Set the LCD panel contrast using 7 gradations from -3 (low contrast) to +3 (high contrast). The default setting is 0. Choose from eight LCD background colors. Sky blue is the default color. Other selections are blue, light blue, green, bright green, yellow, purple, and pink. Press ENTER to reset the Free counter. Start the cleaning function to clean the card feed rollers and heated rollers, and to clean the magnetic head when using magnetic stripe cards. See “Cleaning the card feed rollers and heat roller” on page 45 or “Cleaning the magnetic head” on page 46 for the steps to follow. RP90 Plus E and RL90 User Guide Using the LCD menus Menu Display Settings Function Ink Retransfer Standby Buzzer Power Saving Bend Remedy Ink Type Displays the type of ink ribbon that is loaded in the printer. YMCK: 0 Datacard supports YMCK and YMCKK ink ribbons. (The printer YMCKPO: 2 detects the type of ink ribbon; it cannot be set.) See your dealer YMCKK: 4 regarding support for YMCKPO ink ribbon. Black level Choose from seven gradations from -3 (lighter) to +5 (darker). Black mode Choose Standard or Fine. Change to Fine if thin lines or small black text is blurred (printing speed is slower). SP - Ink1 Level Use SP - Ink1 and Ink2 levels to set the darkness level of special inks that will be available in the future. SP - Ink2 Level See SP -Ink1 Level above. Media type: Datacard retransfer ribbon is available in 1000 frames per roll. 750 1000 Temp Level Set the retransfer roller temperature. Set from -3 (lower) to +2 (higher). Speed (front) Set the retransfer speed for the front of the card. Set from -10 (slower) to +2 (faster). Initialize the retransfer film after making changes. See “Initialize the retransfer film” on page 17. Speed (back) Set the retransfer speed for the back of the card. Set from -10 (slower) to +2 (faster). Initialize the retransfer film after making changes. See “Initialize the retransfer film” on page 17. MG Print (JIS) Select ON or OFF. Front Wait When printing both sides of a card and using an optional Back Wait smart card (IC) unit, specifies whether to wait after the front side or the back side of the card. ON or OFF Use to turn the electronic beep sound ON or OFF. The sound can indicate an error, when fewer than 20 cards remain in the card hopper, or to confirm a menu selection. OFF or up to 60 minutes The printer enters power save mode after a specified period of inactivity. Choose from OFF or select from 5 to 60 minutes in 5 to15 minute increments. “Sleeping” appears on the LCD display. To cancel power save mode, press RESET and then the ENTER key. The printer uses one set of supplies. Temp Level Choose from -5 (lowe...
Эта инструкция также подходит к моделям:Принтеры - RL90 (3.91 mb)