Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
See Figure 10 NOTE: Be very careful not to damage or distort the thin Mylar Recovery Blade next to the wiper blade. If this blade is bent or damaged in any way, it should be replaced. 8) Coat the new wiper blade with your preferred lubricant, and install the wiper blade and two screws. Remember to use the smaller screws. See Figure 11 Figure 12 Figure 13 9) Remove the fill plug from the toner supply and dump/vacuum out the remaining toner. See Figure 12 10) Remove the screw on the doctor blade spring holder. Remove the entire spring and holder assy. See Figure 13 DOC-0331 Page 5 Lexmark E-321/E323 Toner Cartridges (Continued) Figure 14 Figure 15 11) On the left side of the toner hopper (fill plug side), pry out the developer roller bushing. See Figure 14 12) Remove the developer roller. Be careful not to damage the black retaining blade. See Figure 15 Figure 16 Figure 17 13) Clean the working edge of the doctor blade with a Scotch-Brite pad and alcohol. See Figure 16 NOTE: The shims on the developer roller are similar to those used on the 4019/39/49 cartridges. The same replacement shims can be used if they become damaged. 14) Replace the developer roller back into the hopper. Make sure that the shims are not damaged, and that the black retaining blade is not damaged. Install the bushing. See Figure 17 DOC-0331 Page 6 Lexmark E-321/E323 Toner Cartridges (Continued) Figure 18 Figure 19 15) Fill the hopper with 225g of E320 toner. Replace the fill plug. See Figure 18 16) Install the doctor blade spring holder, spring and screw. See Figure 19 Figure 21 Figure 20 17) Install the waste chamber into the right end cap. Install the 2 screws. See Figure 20 18) Install the drum (gear side) into the right end cap. See Figure 21 DOC-0331 Page 7 Lexmark E-321/E323 Toner Cartridges (Continued) Figure 23 Figure 22 19) Install the spring large loop side on the large toner hopper post. See Figure 22 20) Install the coupler gear on to the shaft on the toner supply. Note that the gear and shaft are both keyed. See Figure 23 Figure 24 Figure 25 21) Install the toner supply hopper into the end cap. See Figure 24 22) While holding the supply hopper in place, take the spring hook, grasp the small loop of the spring and place it on the small end cap post. See Figure 25 DOC-0331 Page 8 Lexmark E-321/E323 Toner Cartridges (Continued) Figure26 Figure27 23) If you have a Prebate cartridge, install the replacement chip in the left end cap. Make sure that the chip is locked in place by the two plastic tabs. See Figure’s 26 & 27 Figure 28 Figure 29 24) Clean off all the old conductive grease from the left end cap. Reapply new grease to all the contact points including a small amount on the drum axle shaft. Remember, when using conductive grease, more is not better. Just use a small amount on each point. See Figure 28 25) Place the large loop of the second spring on the large hopper post. See Figure 29 DOC-0331 Page 9 Lexmark E-321/E323 Toner Cartridges (Continued) Figure 31 Figure 30 26) Carefully align and install the left end cap. Make sure the back brace fits correctly and that the alignment pins are all in there correct position. Snap the end cap in place. See Figure’s 30 & 31 Figure 33 Figure 32 27) With the spring hook, grasp the small loop of the spring and place it on the small end cap post. See Figure 32 28) Install the three screws on the end cap. See Figure 33 DOC-0331 Page 10 Lexmark E-321/E323 Toner Cartridges (Continued) Figure 35 Figure 34 29) With the springs in the correct position, bend the drum cover slightly in the middle. Place the alignment pins in their respective slots. Try to make sure the large tail of the spring fits in place as you fit the cover in place. See Figure’s 34 & 35 The cartridge is finished! If you are testing the cartridge, (Highly recommended) a test page can be generated from the machine, but it is not an easy process. It is easier and faster to generate pages from an Anacom box, or a computer. 30) Once the testing is finished, make sure you install the shipping lock. PrintingaTestpage: As stated above running test prints from the machine itself is not an easy task. It is easier and faster to run tests from an Anacom box, or a computer. If you need to run prints from the machine do the following: 1)Turn the printer off. 2)Open the top cover. 3)Press and hold the “CONTINUE” button as you turn the printer back on. All the lights will cycle. 4)Release the “CONTINUE” button, close the cover. 5)Press and hold the “CONTINUE” button until all the lights cycle. 6)The Printer will print the Configuration Page. LightSequences: The more common problems such as Toner Low and Paper Jam have their own lights and are self-explanatory. I will list some of the less apparent sequences here. Toner Low Blinking, Error on steady: Toner cartridge error Toner Low Blinking, Error Blinking: Wrong Toner ...
Эта инструкция также подходит к моделям:Принтеры - LEXMARK E-321 (6.13 mb)