Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Note . If you press the { {{{{Proof} }}}} key or the { {{{{Print} }}}} key after setting Security mode, the beeper sounds and you cannot make prints. . You cannot cancel Security mode even if you turn off the main switch. . If you make the next master, Security mode is canceled. . You cannot pull out the drum unit before making the next master. 44 2. Optional Functions Optional Document Feeder Insert a stack of originals in the document feeder. They will be fed automatically. Originals Placing the following originals in the document feeder might cause misfeeds or damage to the originals. Place the following kinds of originals on the exposure glass: • Originals heavier than 127.9g/m2, 34 lb • Originals lighter than 52.3g/m2, 14 lb • Originals smaller than 148mm . 210mm, 5.9" . 8.3" • Originals larger than 297mm . 864mm, 11.6" . 34.0" • Stapled or clipped originals • Perforated or torn originals • Curled, folded, or creased originals • Originals with any kind of coating, such as thermal fax paper, art paper, aluminum foil, carbon paper, or conductive paper • Bound originals such as books • Damaged originals • Originals with glue on them • Pasted originals • Originals written in pencil • Thin originals that are a little stiff • Originals with index tabs • Transparent originals such as OHP transparencies or translucent paper The following original sizes placed in the document feeder can be detected. Metric version A3 L, B4 L, A4 KL, B5 KL, A5KL Inch version 11" . 17" L, 81/2" . 14" L, 81/2" . 11"KL, 51/2" . 81/2"KL Note . Place originals after correction fluid and ink have completely dried. Not taking this precaution could mark the exposure glass and cause marks to be printed. For standard printing functions, set originals as shown below. R R GRSETT1E You cannot place originals of differ ent sizes at the same time. When you use thin originals, place one original at a time in the document feeder or place them on the exposure glass. The first 5mm, 0.2", of the leading edge and the last 2mm, 0.08" of the trailing edge cannot be printed. Make sure the leading edge margin is at least 5mm, 0.2", and the trailing edge margin is at least 2mm, 0.08". Do not stack originals above the limit mark. Optional Functions 2 Placing Originals in the Document Feeder A AAAAAdjust the guide to the original size. B BBBBInsert the aligned originals face up in the document feeder until they stop. ZDCH120E Limitation . Approximately 50 originals (80g/m2, 21 lb) can be inserted at one time in the document feeder. The first (top) original will be fed first. Note . To avoid a multi-sheet feed, shuffle the originals before placing them in the document feeder. . The guides must fit snugly against both sides of the stack. C CCCCMake the desired settings, and then enter the number of prints with the number keys. D DDDDpress the { {{{{Start} }}}} key. Printing starts automatically after trial print is delivered. Note . If you want to check the print image, press the { {{{{Auto Cycle} }}}} key to turn off Auto Cycle mode before pressing the { {{{{Start} }}}} key. For details, see p.14 “When Auto Cycle is off”. 46 Optional Document Feeder Combining Originals Using the Document Feeder Reference For details about Combining Originals, see p.39 “Combining Originals”. A AAAAPress the { {{{{Combine} }}}} key. B BBBBCheck the print paper size, and then select the desired reproduction ratio. C CCCCInsert the 2 originals face up in the document feeder. ZDCH120E Note . The first original will be printed on the left side of the paper. D DDDDEnter the number of prints with the number keys. E EEEEPress the { {{{{Start} }}}} key. Printing starts automatically after trial print is delivered. Note . If you want to check the print image, press the { {{{{Auto Cycle} }}}} key to turn off Auto Cycle mode before pressing the { {{{{Start} }}}} key. For details, see p.14 “When Auto Cycle is off”. . After the first original is on the master, the second original is fed. . If you place only one original, the beeper sounds after the first original is on the master. Place the second original and the desired image settings. Then, press the { {{{{Start} }}}} key. Optional Functions Memory Mode Using the Document Feeder Reference For details about Memory mode, see p.36 “Memory Mode”. A AAAAPress the { {{{{Memory/Class} }}}} key to light the memory indicator. B BBBBWith the number keys, enter the desired number of prints for the first original. C CCCCPress the { {{{{q qqqq} }}}} key. This stores the number of prints to be made for the first original in memory 1. D DDDDRepeat steps B BBBB and C CCCC for each original. Note . The number of prints for up to 25 originals can be stored. E EEEEPress the { {{{{q qqqq} }}}} key again. The memory returns to memory 1. Note . If you store the number of prints for 25 originals, the memory number returns to 1. It is not necessary to press the { {{{{q qqqq} }}}} key. 2 48 Optional Document Feeder F FFFFInsert originals face up in the doc-H H...
Эта инструкция также подходит к моделям:Принтеры - JP1030 (4.64 mb)