Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Otherwise, burning or injury of hand may result. — 17 — 4.2 Removing Jammed Paper 4.2 Removing Jammed Paper 1. Turn the printer power off. 2. Open the printer cover. 3. Remove the jammed paper including any paper chips remaining. (Remove the paper roll set in the holder as well.) 4. Reinstall the paper roll and close the printer cover. 5. Turn on the printer. The auto cutter mechanism is initialized and the alarm is cleared. CAUTION! ¦ If the cutter blade remains protruded with paper jammed, press the FEED button. If the cutter blade does not move back, performe the above step 1 through 3 and then turn the printer on without a paper roll. Contact your Citizen Systems dealer. Be carefull not to have your hand injured by the cutter blade in the operation. ¦ The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touch the heating element of the head with a bare hand or metal object either. 4.3 Cleaning the Print Head 1. Turn the printer power off. 2. Open the printer cover. 3. Wait several minutes. Wipe off any debris on the heating element of the head using a cotton swab soaked in ethyl alcohol. Print (thermal) head CAUTION! The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touch the heating element of the head with a bare hand or metal object either. — 18 — 4.4 Self-printing 4.4 Self-printing Insert paper into the printer. With the FEED button pressed and held, turn the printer power on, keep the FEED button held for about 1 second, and then release the FEED button. The printer starts self-printing. The printer prints model name, version, DIP switch setting, memory switch setting, and built-in fonts. Memory switch setting Serial communication condition (Only serial interface model) DIP switch setting (Only serial interface model) Firmware version Interface Buffer size 4.5 Hexadecimal Dump Printing This function is to print all received data in hexadecimal numbers. If problems such as missing data, data duplication, etc. should occur, this function allows checking whether or not the printer is receiving data correctly. Set paper to the printer and keep the printer cover open. With the FEED button pressed and held, turn the printer power on and then close the printer cover. The printer prints “HEX dump print mode” followed by the received data printed in hexadecimal numbers and some characters. CAUTION! ¦ The printer prints “.” if there is no characters corresponding to data. ¦ During hexadecimal dump, functions except some command will be disabled. ¦ If print data DOES NOT cover a line, press the FEED button to print the line. When you press the FEED button three times consecutively, or you turn the printer power off, or the printer receives a reset signal from the interface, the hexadecimal dump printing is terminated. Print example HEX DUMP PRINT MODE 1B 21 00 1B 20 04 41 42 43 44 .!.. .ABCD 45 46 47 48 49 4A 4B 4C 4D 4E EFGHIJKLMN 4F 50 0D 0A 31 32 33 0D 0A OP..123.. — 19 — 4.6 Error Indication 4.6 Error Indication . Paper end Paper empty is detected in two steps: paper near-end and paper end. It causes the ERROR LED to light. If paper end is detected, refill the paper. If the printer cover is open, a paper-end is detected. . Printer cover open During printing, do not open the printer cover. If you open the printer cover accidentally, the ERROR LED blinks. Check the paper, pull the paper straightforward by several cm out of the printer, and then close the printer cover. Printing resumes automatically. Sending a command to resume printing may be required depending on the memory switch setting. . Cutter lock If the cutter blade stops operating due to paper jam or the like, the ERROR LED blinks. Remove the cause of the trouble and press the FEED button. If the blade still does not move and the cover cannot be opened, contact your Citizen Systems dealer. . Thermal head overheat When you print dense characters or dark image, the head temperature rises. If the head temperature exceeds a specified level, the printer stops printing operation and waits till the head temperature is lowered. During waiting, the ERROR LED blinks. When the head temperature is lowered, printing resumes automatically. . Power switch operation error If you turn power on again just after powering off, an error may occur. Before turning power on again, wait till POWER LED goes off completely after powering off. — 20 — Lighting and blinking status of each error including the above is shown below. Status POWER LED ERROR LED Buzzer Paper-end Lights Lights Paper near-end Lights Lights Cover open error Lights Lights Cover open error *1 Lights Cutter lock error Lights Head overheat error Lights Motor overheat error Lights Memory check error Lights Low voltage error Lights High voltage error or Lights Power switch operation error Macro execution Lights wait *2 Wait for cutting label OFF *L Paper detection error OFF *L *1: When the printer is printing. *2: The ERROR LED may bl...
Эта инструкция также подходит к моделям:Принтеры - CT-S2000 (1.48 mb)
Принтеры - CT-S2000DC (1.48 mb)
Принтеры - CT-S2000DCL (1.48 mb)