Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
From time 0:00 press the LEFT key ten times. The display will show then the transmitter address. Press the LEFT key to exit this function. The transmitter address is required to be equal to the Receiver. (Fig. 55) Select, through setting of the dip switches, the address of the receiver. (Fig. 57) Switch #8 must always be in the ON position (down). It is also possible to start a receiver address search sequence through the Transmitter. To enter this function use the DOWN or UP keys until the cursor (small triangle) is left of the clock icon. From time 0:00 press the LEFT key tem times. The display will then show the present transmitter address. To alter the address of the Transmitter press the UP key to increase and DOWN to decrease it. A “beep” from the Receiver will confirm the same address as the Transmitter. Press LEFT key to exit this function. Note: The address of the Receiver is acquired only at its power on. Changing the address while the Receiver is powered will not have any effect. To change the address of the Receiver, disconnect the power cable from the Receiver, change the address and reconnect the power cable to the Receiver. FIGURE 55 FAHRENHEIT - Celsius Temperature Indication It is possible to set the Remote Control to display the temperatures in either Fahrenheit or Celsius. Use the UP or DOWN key on the Transmitter until the cursor (small triangle) is left of the click icon. From time 0:00 press the LEFT key ten times. The display will show the transmitter address. Use the RIGHT key to toggle from .F to .C and vice versa. The display will show the selected unit of measure. Press the LEFT key to exit this function. (Fig. 56) FIGURE 56 W415-0583 / D / 07.24.07 DIP SWITCH NUMBER (0 = ON / 1 = OFF) DIP SWITCH NUMBER (0 = ON / 1 = OFF) FIGURE 57 W415-0583 / D / 07.24.07 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of paints and lubricants used in the manufacturing process and will not occur again. Simply open a window to sufficiently ventilate the room. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to suffi ciently ventilate the room. Purge all gas lines with the glass door of the fi replace open. Assure that a continuous gas flow is at the burner before closing the door. A. This fireplace is equipped with a pilot which must be lit by hand while following these instructions exactly. B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor. C. Use only your hand to turn the gas control knob / manual shut-off knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a qualified service technician. Force or attempted re pair may result in a fire or explosion. D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water. GAS KNOB • Do not touch any electric switch. • Do not use any phone in your building. • If you cannot reach your gas supplier, call the fire department. • Turn off all gas to the fireplace. • Do not try to light any appliance. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. FOR YOUR SAFETY READ BEFORE LIGHTING: WHAT TO DO IF YOU SMELL GAS FIGURE 58 LIGHTING INSTRUCTIONS Warning: if you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Initial lighting of the pilot and main burners must be done with the glass door off. Do not connect valve or wall switch to electricity. See insta llation instructions. When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob it depressed slightly. 1. STOP! read the safety information on the operating label. 2. Turn off all electric power to the fireplace. 3. Turn the gas knob clockwise to off. 4. Wait 5 minutes to clear out any gas. If you smell gas, including near the floor, STOP! Follow “B” on the op erating label. If you don’t smell gas, go to the next step. 5. If the fireplace is equipped with a flame adjustment valve, turn clockwise to off. 6. Find pilot located in front of the back log on the right side. 7. Turn gas knob counter-clocwise to pilot. 8. This unit is equipped with an auto-spark. Depress and hold gas knob . Keep knob fully de pressed for one minute, then release. If pilot does not continue to burn repeat steps 3 through 7. 9. With pilot lit, turn gas knob counter-clockwise to on. 10. If equipped with flame adjustment valve, push and turn knob to high. 11....
Эта инструкция также подходит к моделям:Принтеры - TUREEN GD82PT-T (2.92 mb)