Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Blowing air may prevent CO from reaching the sensors. • In direct sunlight. • In outlets covered by curtains or other obstruction. • This CO Alarm is designed for use inside a single-family home or apartment. It is not meant to be used in common lobbies, hallways, or basements of multi-family buildings unless working CO Alarms are also installed in each family living unit. CO Alarms in common areas may not be heard from inside individual family living units. • This CO Alarm alone is not a suitable substitute for complete detection systems in places which house many people, like hotels or dormitories, unless a CO Alarm is also placed in each unit. • DO NOT use this CO Alarm in warehouses, industrial or commercial buildings, special-purpose non-residential buildings, or airplanes. This CO Alarm is specifically designed for residential use, and may not provide adequate protection in non-residential applications. ALARM LEVELS OF CO ARE DETECTED: HORN: Sounds loudly -4 beeps, pause, 4 beeps, pause. This sequence repeats for as long as the unit is in alarm.* POWER/ALARM LIGHT: The LED flashes with the same pattern as the horn. *Note: If unit goes into alarm under battery back-up power, the regular 4 beeps-brief pause cycle will repeat for four minutes. After four minutes, the pause will increase to 1 minute. IF YOU SILENCE THE ALARM: HORN: Silent for about 4 minutes POWER/ALARM LIGHT: Flashes rapidly Note: After 4 minutes, if CO levels drop below alarm levels, the unit will remain silent and return to normal operation. If CO presence still indicates a potentially dangerous situation, the horn will sound again. IF THE CO LEVELS RETURN TO NORMAL: HORN: Silent POWER/ALARM LIGHT: Shines continuously INSTALLATION WHERE TO INSTALL CO ALARMS The National Fire Protection Association (NFPA) recommends that a CO Alarm should be centrally located outside of each separate sleeping area in the immediate vicinity of the bedrooms. For added protection, install additional CO Alarms in each separate bedroom, and on every level of your home. If your bedroom hallway is longer than 40 feet (12 meters), install a CO Alarm at BOTH ends of the hallway. G BEDROOM BEDROOM HALLLIVING ROOM KITCHEN BASEMENT BEDROOM In a Single-level Home: • Install at least one CO Alarm near or within each separate sleeping area. • For added protection, install an additional CO Alarm at least 20 feet (6 meters) away from the furnace or fuel burning heat source. In a Multi-level Home: • Install at least one CO Alarm near or within each separate sleeping area. • For added protection, install at least one CO Alarm on each level of the home. If you have a basement, install that CO Alarm at the top of the basement stairs. • For added protection, install an additional CO Alarm at least 20 feet (6 meters) away from the furnace or fuel burning heat source. This unit should receive continuous electrical power. (The battery is meant for emergency back-up only). Choose an outlet where it cannot be accidentally unplugged or switched off by children. Keep small children away from the unit. Teach them not to play with it or unplug it. Explain what the alarms mean. REQUIRED TO MEET NFPA RECOMMENDATIONS SUGGESTED AREAS FOR INSTALLING ADDITIONAL CO ALARMS 2 HOW TO INSTALL YOUR CO ALARM Read “Where To Install CO Alarms” before starting. Before you start installation, find the pair of self-adhesive labels included with this CO Alarm. On each label write in the phone number of your emergency responder (like 911) and a qualified appliance technician. Place one label near the CO Alarm, and the other label in the “fresh air” location you plan to go if the alarm sounds. IF YOUR CO ALARM SOUNDS Quick reference: • Install the two (2) AA batteries to activate the battery back-up. • Plug the Alarm into a standard 120V unswitched outlet. • Test the CO Alarm. ACTIVATE THE BATTERY BACK-UP 1. Open the battery compartment on the front of the Alarm. 2. Install both AA batteries inside the battery compartment as indicated. Make sure the “+” and “–” ends of each battery are aligned properly. 3. Close the battery compartment completely. The battery back-up is designed to provide emergency power to the CO Alarm for at least 7 days. Actual back-up time depends on the strength (freshness) of the battery. The battery back-up will not work unless a good battery is properly installed. PLUG THE ALARM INTO AN OUTLET 1. Plug the unit into a standard UNSWITCHED 120V AC outlet. The unit should be located where it can wake you if it AC Plug alarms at night. 2. Make sure the POWER/ALARM light shines continuously when you plug it in. 3. Test by pressing the Test/Silence button firmly until the unit sounds: four loud beeps, pause, 4 beeps. During testing, the POWER/ ALARM light will flash rapidly. This is normal. “ALARM-MOVE TO FRESH AIR” If you hear the alarm horn and the red light is flashing, move everyone to a source of fresh air. DO NOT unplug the CO Alarm! Alarms have various limitations. See "General ...