Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
1 HOW TO INSTALL THIS SMOKE ALARM THE PARTS OF THIS SMOKE ALARM 2 1. Test/Silence button 2. Battery drawer 3. Power indicator LED 4. Smoke Alarm LED TOOLS YOU WILL NEED: This unit is designed to be mounted on the ceiling, or on the wall if necessary. • Pencil • Drill with 3/16” (5 mm) drill bit • Phillips screwdriver • Hammer • Pliers to activate optional “tamper-resistant” locking features QUICK INSTALLATION INSTRUCTIONS 1. Insert the batteries into the battery drawer of the first Alarm and close the drawer. 2. The Alarm will sound with a chirp. 3. If you purchased the Talking Smoke and Carbon Monoxide Alarm, you will now be prompted to set the Alarm's location. Follow the direction given by the Alarm. NOTE: Steps 4 through 6 need to be completed within two minutes. If more than two minutes pass, the Green power LED will stop blinking. Simply open the battery drawer of the second Alarm and repeat steps 4 through 6. 4. Insert the batteries into the battery drawer of the next Alarm. DO NOT CLOSE THE DRAWER. 5. Press and hold the test button and then close the battery drawer. 6. Once you hear the unit chirp, release the test button. The Green power LED will start to blink indicating the ONELINK® Alarm is waiting for program data from one of the other setup ONELINK® Alarms. 7. Press and hold the test button on the first Alarm, until the second Alarm chirps and its Green power LED stops blinking. Then release the test button. 8. If you purchased a Talking Smoke Alarm, you will now be prompted to set the Alarm's location. Follow the directions given by the Alarm. 9. If you have purchased the hardwired battery back-up ONELINK® Alarm, you can now connect the hardwired Alarm by installing the three-wire connector on the ceiling to the Alarm. 10. Repeat steps 4-9 for additional ONELINK® Alarms. You have now successfully linked your new ONELINK® Alarms. To add additional Alarms at a later time, follow steps 4 through 9. FOLLOW THESE SIMPLE STEPS! If you want to lock the battery drawer, or lock the Smoke Alarm to the mounting bracket, please read the “Optional Locking Features” section before you begin installation. 1. Hold base firmly and twist the mounting bracket counterclockwise to separate it from the base. 2. Hold the mounting bracket against the ceiling (or wall) so the vertical mounting slot is aligned in the 12 o’clock position and trace around the inside of the mounting slots (vertical and horizontal mounting). 3. Put the unit where it won’t get covered with dust when you drill the mounting holes. 4. Using a 3/16” (5 mm) drill bit, drill a hole through the center of the oval outlines you traced. 5. Insert the plastic screw anchors (in the plastic bag with screws) into the holes. Tap the screw anchors gently with a hammer, if necessary, until they are flush with the ceiling or wall. 6. Line the mounting bracket up over the plastic screw anchors. 7. Screw the mounting bracket to the ceiling or wall through the mounting slots using the two screws provided. 8. Attach the Smoke Alarm to the mounting bracket. Line up the guides on the alarm’s base with the guides on the mounting bracket.When guides are lined up, turn the base clockwise (right) until it snaps into place. NOTE: Once the Smoke Alarm is snapped onto the mounting bracket, you can rotate the Smoke Alarm to adjust the alignment. 9. Test the Smoke Alarm. See “Weekly Testing.” 3 TO LOCK THE BATTERY COMPARTMENT Do not lock the battery compartment until you install the batteries and test the Smoke Alarm. If the unit does not alarm during testing, DO NOT lock the battery compartment! Install new batteries and test again. If the Smoke Alarm still does not alarm, replace it immediately. 1. Using needle-nose pliers, detach one locking pin from the mounting bracket. 2. After batteries are inserted, then push the locking pin through the hole near the battery door latch on the back of the Smoke Alarm. OPTIONAL LOCKING FEATURES TO LOCK THE MOUNTING BRACKET 1. Using needle-nose pliers, detach one locking pin from the mounting bracket. 2. Insert the locking pin through the hole on the back of the Smoke Alarm as shown in the diagram. 3. When you attach the Smoke Alarm to the mounting bracket, the locking pin’s head will fit into a notch on the bracket. The optional locking features are designed to prevent unauthorized removal of the battery or alarm. It is not necessary to activate the locks in single-family households where unauthorized battery or alarm removal is not a concern. These Smoke Alarms have two separate locking features: one to lock the battery compartment, and the other to lock the Smoke Alarm to the mounting bracket. You can choose to use either feature independently, or use them both. Tools you will need: • Needle-nose pliers • Standard flathead screwdriver. Both locking features use locking pins, which are molded into the mounting bracket. Depending on which locking features you use, remove one or both pins from the mounting bracket using needle-nose p...