Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The TSD-90A transmitter is compatible with any Linear SX format supervised security receiver. The TSD-90A sounds a local alarm as soon as smoke is detected. Twenty seconds after the local alarm sounds, the TSD-90A’s transmitter will send an alarm signal to the supervised receiver. The alarm signal will be repeated every 20 seconds as long as smoke is still present. A restoral report will be sent when the smoke detection chamber clears. Supervisory status reports are sent from the TSD-90A every hour. Coding switches are not required or used in the TSD-90A. Each transmitter is pre-coded at the factory to a unique code. With the SX format, there are more than sixteen million codes possible. The smoke alarm and transmitter are powered by two 9-volt batteries. These batteries are supplied with the transmitter and can power the unit for up to two years. If the battery voltage drops below a preset level, a low battery report is sent to the receiver with any status, alarm, tamper or test transmission. NOTE: After replacing batteries, press transmitter test button to reset “low battery circuit”. STEP 1 Remove mounting plate. Remove the TSD-90A mounting plate by turning the plate counterclockwise. STEP 2 Identify components. Examine the TSD-90A to identify the component locations. STEP 3 Install batteries. Connect the two 9-volt batteries and place them into battery holding cups. STEP 4 Pick smoke alarm location. Referring to the NFPA standard on the back of this sheet, select a good location to mount the TSD-90A. Mounting the TSD-90A on foil-backed wallpaper or on a metal single-gang electrical box is not recommended because the radio range will be reduced. STEP 5 Install mounting plate. Use the two screws and anchors provided to attach the mounting plate to the wall or ceiling. Alternately, the mounting plate can be attached to a plastic single-gang electrical outlet box. For the best radio range, observe the “best signal” label on the bottom of the unit. STEP 6 Program TSD-90A into receiver and test. Follow the receiver’s instructions to set it in a program or learn mode. Press the TSD-90A’s transmitter test button (not the smoke alarm’s test button) to send a test signal. The transmit LED should light. Verify that the signal was received and that the transmitter was properly entered into the receiver’s memory. TWIST MOUNTING PLATE TO UNLOCK REMOVE MOUNTING PLATE BATTERY COMPARTMENTS TRANSMITTER BOARD TRANSMIT LED TRANSMITTER TEST BUTTON PLASTIC SINGLE-GANG ELECTRICAL BOX SCREW ANCHORS FOR WALLBOARD OR PRESS TEST BUTTON SX FORMAT! CONNECT AND INSTALL TWO 9-VOLT DURACELL MN1604 ALKALINE OR TWO ULTRALIFE U9VL LITHIUM BATTERIES (BOTH MUST BE THE SAME TYPE) STEP 7 Atach TSD-90A to mounting plate. Match up STEP 8 Test smoke alarm. Set the receiver into a test STEP 9 Complete receiver programming. Refer to the alignment tabs on alarm and plate. Turn alarm clockwise until mode. Press and hold the smoke alarm test button. Continue instructions supplied with the supervised receiver to program it locks in place (tamper switch will click as alarm locks onto to hold the test button for at least 30 seconds after the the TSD-90A as a 24-hour fire alarm. Repeat the previous step plate). noisemaker starts. Verify that the signal was received. to verify that the TSD-90A triggers the correct zone on the receiver and that the correct report is sent to the central station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (if the system is monitored). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NFPA 72 STANDARD FOR SMOKE ALARM LOCATION The installation of smoke alarms in kitchens, attics (furnished or unfurnished), or garages is If you have to go through a closed door, carefully feel the door and door knob to see if undue The TSD-90A should be installed in accordance with National Fire Protection Association not normally recommended, as these locations occasionally experience conditions that can heat is present. If they seem relatively cool, brace your foot against the bottom of the door (NFPA) Standard 72, which reads as follows: result in improper operation. with your hip against the door and one hand against the top edge. Open it slightly. If a rush 2-1.1.1 Smoke alarms shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit including basements and excluding crawl spaces and unfinished attics. In new construction, a smoke alarm shall be installed in each sleeping room. 2-1.1.2 For family living units with one or more split levels (i.e., adjacent levels with less than one full story separation between levels), a smoke a...