Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Within hours of starting a vehicle and backing it out of the garage, the levels present over time can activate the alarm and become a nuisance. • In the kitchen, some gas appliances can emit a short burst of CO or gas upon startup. This is normal. If your CO and Gas Alarm is installed too close to these appliances, it may alarm often and become a nuisance. • Keep alarms at least 20 feet (6m) from the sources or combustion particles (stove, furnace, water heater, space heater), if possible. In areas where a 20 foot (6m) distance is not possible (in modular, mobile or smaller homes for example), it is recommended the alarm be placed as far from these fuel-burning sources as possible. The placement recommendations are intended to keep these alarms at a reasonable distance from a fuel-burning source and reduce "unwanted" alarms. Unwanted alarms can occur if an alarm is placed directly next to a fuel-burning source. Ventilate these areas as much as possible. If you must install the alarm near a cooking or heating appliance, install at least 5 feet (1.5m) from appliance. • Curtains or heavy furniture may prevent CO or gas from reaching the sensor. • Less than 12 inches (306mm) away from fluorescent lights. Electrical noise can interfere with the sensor. • In extremely humid areas. This alarm should be at least 10 feet (3m) from a bath or shower, sauna, humidifier, vaporizer, dishwasher, laundry room, utility room or other source of high humidity. • In very cold or very hot environments or in unheated buildings or outdoor rooms where the temperature can go below or above the operating range of the alarm. Temperature limits for proper operation are 40o to 100oF (4.4o to 37.8oC). • In turbulent air, such as near ceiling fans, heat vents, air conditioners, fresh air returns or open windows. Blowing air may prevent CO from reaching the sensors. Page 4 • Good ventilation is recommended when household cleaning supplies or similar contaminants are used. • Excessive spillage or reverse venting of fuel-burning appliances caused by outdoor ambient conditions, such as: 0 Wind direction and/or velocity, including high gusts of wind. Heavy air in the vent pipes (cold/ humid air with extended periods between cycles). 0 Negative pressure differential resulting from the use of exhaust fans. 0 Simultaneous operation of several fuel-burning appliances competing for limited internal air. 0 Vent pipe connections vibrating loose from clothes dryers, furnaces or water heaters. 0 Obstructions in or unconventional vent pipe designs which can amplify the above situations. HOW TO INSTALL THIS CO AND GAS ALARM IMPORTANT: Read all instructions before using this product. 1. Determine the best location for your CO and Gas Alarm. 2. Your alarm is equipped to be mounted as a direct plug-in unit. The unit can be plugged directly into a wall outlet. 3. Activate the 9 Volt battery. Remove and discard the pull tab. Make sure the battery door is closed and latched. 4. The green power LED should be on continuously. It may take up to 3 minutes for the alarm to begin monitoring for CO and gas. 5. Test the alarm following installation and weekly thereafter. NOTE: For your convenience, we provide separate labels for the French-language product markings. If you choose to utilize those markings, remove the label from the backing and apply it to the alarm. Carefully align the label in the appropriate space and press firmly to ensure the label permanently adheres to the alarm. WHAT YOU SHOULD DO IF THE ALARM SOUNDS Never disconnect your CO and Gas Alarm to silence an alarm. The alarm will automatically sense when the level of CO and natural gas in the air falls below the danger level. You should stay outside the residence in fresh air until the alarm is silenced. When the alarm sounds, do not stand too close to the alarm. The sound produced by the alarm is loud because it is designed to awaken a person in an emergency. Prolonged exposure to the alarm at a close distance may be harmful to your hearing. Two self-adhesive labels have been provided with instructions indicating what to do if the alarm sounds. Add the phone numbers of your emergency services provider and a qualified technician to each label. Place one of the labels in a visible area next to the alarm and place the other label near a source of fresh air which will be used as a gathering place if the alarm sounds. READ CAREFULLY. THIS UNIT IS SEALED. THE ALARM COVER IS NOT REMOVABLE! Leave your CO and Gas Alarm plugged in year-round. CO and gas problems can occur any time during the year and this alarm can only alert you if it is plugged in and receiving power. This Alarm is intended for use in a standard, unswitched 120VAC wall outlet. It is not intended for use in extension cords, power strips or outlets controlled by a switch or dimmer. These may not provide continuous power to the unit. When fully powered, it samples the air continuously. A microchip inside the unit ...
Эта инструкция также подходит к моделям:Пожарные сигнализации - MCN400LCN (386.89 kb)
Пожарные сигнализации - MCN400CN (386.89 kb)
Пожарные сигнализации - MCN600LCN (386.89 kb)
Пожарные сигнализации - MCND401CN (386.89 kb)