Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Use the screws and anchors provided to secure the mounting plate. 6.5 The battery is INSTALLED REVERSED FOR SHIPPING. Remove and reinstall the battery in the correct orientation as noted on the inside of the battery door. When installing the battery, align the “+” and “-” battery terminals on the correct contacts. The alarm will beep once indicating proper battery installation. WARNING: BATTERY IS REQUIRED FOR ALARM OPERATION AND DETECTION OF CARBON MONOXIDE. IF NO BATTERY IS INSTALLED, THE BATTERY DOOR WILL NOT CLOSE EASILY AND THE UNIT WILL NOT ATTACH TO THE MOUNTING BRACKET. 6.6 Align marks on the edge of the trim plate with those on the alarm. Twist the alarm in the direction indicated by the “ON” arrow on the alarm cover (see step D) until it locks in place. 6.7 To make your carbon monoxide alarm tamper resistant, a locking pin has been provided in the bag with the screws and anchors. Using this pin will deter children and others from removing the alarm from the mounting plate. To use the pin, insert it into the hole in the side of the alarm after the alarm has been installed on the mounting plate (see fig. 3). Note the tamper resist pin will have to be removed in order to change the battery. Using long nose pliers pull the pin out of the hole, it is now possible to remove the alarm from the mounting plate. Test alarm immediately following installation and weekly therafter for proper operation by pushing the test button until a short beep is heard (approximately three seconds). Release the button. The alarm will then test itself for proper operation and the RED LED will flash 5 times. At completion of the self-test, the alarm will sound 2 patterns. The alarm then resumes normal operation. 6.8 This box contains two self-adhesive labels. You should write the telephone numbers of the emergency service provider and a qualified technician in the space provided in the labels. Place one label next to the alarm, and the other label near a source of fresh air where you plan to gather after the alarm indicates the presence of carbon monoxide. 7.0 ALARM SIGNALS 7.1 NORMAL OPERATION---RED LED flashes once every 30 seconds, indicating that the alarm is powered and active. 7.2 ALARM CONDITION---RED LED turns “on” for 2 seconds and “off” for 4 seconds with 4 short beeps for 1 second and 5 seconds of silence. Pushing and holding the test/reset button for 3 seconds will silence the alarm for about 4 minutes. After 4 minutes, the alarm will once again sound until the unsafe CO concentration is reduced. 7.3 TROUBLE/SERVICE CONDITION---The detector self-tests every 10 minutes. The detector will beep and the Indicator/Test button will flash once every 30 seconds if a fault is detected. This is an indication of a malfunction and that the detector requires immediate servicing. 7.4 LOW BATTERY---RED LED flashes and horn chirps once every 30 seconds for a minimum of (7)days. Replace battery when this signal occurs 8.0 MAINTENANCE – CLEANING YOUR ALARM: WARNING: Do not use any household cleaning agents, paints, varnishes or any other chemical on your 9RV alarm. 8.1 To clean your alarm remove it from the mounting bracket as outlined in Section 6.2. 8.2 You can clean the interior of your alarm by using your vacuum cleaner hose and vacuuming throughthe openings around the perimeter of the alarm. 8.3 The outside can be wiped with a clean towel. Test your alarms weekly and repair or replace them when they no longer function. As with any electronic product, it has a limited life. Alarms that do not work cannot warn you. 8.4 After cleaning, reinstall your alarm and test your alarm by using the TEST button. NOTE: REGULAR TESTING IS RECOMMENDED. 9.0 BATTERY REPLACEMENT IF TAMPER RESISTANT PIN HAS BEEN USED, REFER TO STEP 6.7 UNDER INSTALLATION INSTRUCTIONS FOR REMOVAL INSTRUCTIONS. (see Figure 3) 9.1 To replace the battery remove the alarm from the mounting plate by rotating the alarm in the direction of the “OFF” arrow on the cover. (see Figure 2, Step D). 9.2 The COSTAR® Model 9RV CO Alarm uses one (1) 9 volt alkaline battery. A fresh battery should last for one year under normal operating conditions. They can be purchased anywhere batteries are sold, such as your local hardware store. 9.3 USE ONLY THE FOLLOWING 9 VOLT BATTERY FOR CO ALARM REPLACEMENT. Alkaline type: DURACELL MN1604 WARNING USE ONLY THE BATTERY SPECIFIED. USE OF DIFFERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT ON THE CO ALARM. CONSTANT EXPOSURE TO HIGH OR LOW HUMIDITY MAY REDUCE BATTERY LIFE. CHECK THE BATTERY MANUFACTURERS SPECIFICATIONS FOR PROPER OPERATING CONDITIONS. Note: Most batteries are not rated below -20°C or above 54°C 10.0 PERIODIC ALARM TESTING Test the alarm weekly for proper operation by pushing the test button until a short beep is heard (approximately three seconds). Release the button. The alarm will then test itself for proper operation and the RED LED will flash 4-6 times. At completion of the self-test, the alarm will sound 2 patterns. The alarm...