Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
If the water line and the direct wire reach into the opening far enough, go to step 10, page 13. If you are installing a new dishwasher, complete all of the following steps: Electrical follow all national and local codes and ordinances for completing electrical supply to cabinet. If you are: use steps: Direct Wiring 3, 4 and 5 Using a power supply cord 3a and 4a 11 English hElpful TIp: Wiring the dishwasher will be easier if you route wire into the cabinet opening from the left side. 3. DIREcT WIRE mEThoD: Cut a 3/4” (1.9cm) hole ”C” in right hand cabinet side, rear or floor. Optional locations are shown. Wood Cabinet: Sand hole until smooth. 3a. poWER supplY coRD mEThoD: Cut a 11/2”(3.8cm) hole “D”in right-hand cabinet rear or side. Optional locations are shown. Wood cabinet:Sand hole until smooth. 4. Run wire into house wiring junction box. Use strain relief method provided with junction box. If no strain relief is provided, install a UL-listed/CSA-certified clamp connector for flexible- type wire. If installing conduit, attach a UL-listed/CSAcertified conduit connector to junction box. 4a. Install a mating, three-prong, grounding- type wall receptable “E”in the cabinet next to the dishwasher opening. Go to step 6. 5. Run other end of wire through cabinet hole. Cable must extend to the left front of cabinet opening. Go to step 6. Install a mating, three-prong, grounding-type wall receptacle “E”in the cabinet next to the dishwasher opening. Go to step 6. WATER lINE E hElpful TIp: Routing the water line through the left side of cabinet opening will make water connection easier. 6. Cut a 1/2”(1.3 cm) minimum hole “F” in left-hand cabinet side,rear or floor. Optional locations are shown. (The hole “F” is about 1-3/5” higher than hole “C” or hole “D”) 7. Measure total length of copper tubing “G” required. attach copper tubing to water line with manual shutoff valve. Carefully feed copper tubing through hole in cabinet (copper tubing will bend and kink easily) until it is far enough into the cabinet opening to connect it to dishwasher inlet on the front left of dishwasher. 12 English 8. Turn shutoff valve “h” to “On” position. flush water into a bucket to get rid of particles that may clog the inlet valve. 9. Turn shut-off valve to “Off” position DRAIN hosE 10. Cut a 1-1/2” (3.8cm) diameter hole in cabinet wall or floor on the side of the opening closest to the sink. 11. Connect drain hose to waste tee or waste disposer following one of the following methods: a waste disposer an air gap 11a. no air gap* 11c. no waste disposer an air gap 11b. no air gap* 11d. *an air gap is recommended 11a. WAsTE DIsposER & AIR GAp 3. Use a rubber hose *connector “l” with spring or screw-type clamps* “M” to connect air gap to disposer inlet “n”. The connection “n” MUST be made P 1. Remove the disposer knockout plug. Cut end of drain hose “I” if needed (do not cut ribbed section). 2. attach drain hose to air gap “j” with large spring-type clamp “K”. If the drain hose was cut, use a 1-1/2” to 2” (3.8 to 5 cm) screw-type clamp*. before drain trap “O” and at least 20” (50.8cm) above the floor where dishwasher will be installed. Go to step 12. 11b. No WAsTE DIsposER & AIR GAp 1. Cut end of drain hose “I” if needed (do not cut ribbed section). 2. attach drain hose to air gap “j” with large spring- type clamp. If the drain hose was cut, use a 1-1/2” to 2” (3.8 to 5 cm) screw-type clamp*. 3. Use a rubber hose *connector “l” with spring or screw-type *clamps “M” to connect air gap to waste tee “P”. This connection “P” MUST be made before drain trap “O” and at least 20” (50.8 cm) above the floor where dishwasher will be installed. Go to step 12. * Parts available from local pumbing supply stores. 13 English 11c. WAsTE DIsposER - WITh No AIR GAp 1. Remove the disposer knockout plug. Do not cut end of drain hose. 2. attach drain hose “I” to disposer inlet “n” with large spring-type clamp “K”. This connecting “n” MUST be made before drain trap “O” and at least 20” (50.8 cm) above the floor where dishwasher will be installed. 3. The drain hose must be looped up and securely fastened to the underside of the counter before going to the drain. Hose loop must be a minimum 30 inches (76.8cm) above floor. (Go to step 12) 11d. No WAsTE DIsposER - WITh No AIR GAp 1. Cut end of drain hose “I” (do not cut ribbed section). 2. Attach drain hose to waste tee “P” with 1-1/2” to 2” (3.8 to 5 cm) screw-type clamp* “M”. The connection “P” MUST be made before drain trap “O” and at least 20” (50.8 cm) above the floor where dishwasher will be installed. 3. The drain hose must be looped up and securely fastened to the underside of the counter before going to the drain. hose loop must be a minimum 30 inches (76.8cm) above floor. (Go to Step 12) hElpful TIp: To reduce the vibration of the hose, keep the hose away from the floor and the edge of the hole where it passes through the cabinet. * Parts available from local plumbing supply stores. Insert drain hose “I” in...