Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions for the consumer’s and local inspector’s use. • Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. • Skill Level – Installation of this dishwasher requires basic mechanical, electrical and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See warranty information. • Completion Time – 1 to 3 Hours. New installations require more time than replacement installations. IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately contact your dealer or builder. Optional Accessories – See the Owner’s Manual for available custom panel kits. FOR YOUR SAFETY Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations described in this booklet, gloves, safety glasses or goggles should be worn. READ CAREFULLY. KEEP THESE INSTRUCTIONS. 206C1559P197 31-30258 07-09 JR TOOLS YOU WILL NEED: ¦ Phillips-head screwdriver ¦ 1/4" and 5/16" nutdriver ¦ 6" Adjustable wrench ¦ Level ¦ Carpenter's square ¦ Measuring tape ¦ Safety glasses ¦ Flashlight ¦ Bucket to catch water when fl ushing the line ¦ 15/16" socket (optional for skid removal) ¦ Gloves For New Installations Only: ¦ Tubing cutter ¦ Drill and appropriate bits ¦ Hole saw set 90° Elbow, Ferrule and Compression Nut Hot Water Line Hand Shut-Off Valve Side and Top Trim Pieces on some models Hole Saw Set Level Thread Seal Tape Air Gap Strain Relief Drain Hose Hose Clamp 1/4" and 5/16" Nutdriver 15/16" Socket Bucket Tubing Cutter Drill and Bits Flashlight Gloves Phillips-Head Screwdriver Carpenter's Square 6" Adjustable Wrench Safety Glasses Installation Preparation 2 Measuring Tape PARTS SUPPLIED IN INSTALLATION PACKAGE: ¦ Two #8-18 x 5/8" Phillips special head screws, to secure dishwasher to underside of countertop ¦ Junction box cover and #10 hex-head screw ¦ Hose clamp ¦ Drain hose (approximately 78" long) ¦ Zip ties ¦ Side and top trim pieces (some models) ¦ Literature, samples and/or coupons ¦ 2 Side-mounting brackets with four #8 pan-head mounting screws for non-wood countertops (some models) MATERIALS YOU WILL NEED: ¦ Ferrule, compression nut and 90° elbow (3/8"NPT external thread on one end, opposite end sized to fit water supply) ¦ Thread seal tape ¦ UL-listed wire nuts (3) ¦ GPF65 side-mount kit if countertop is granite or similar material Materials Needed for New Installations: ¦ Air gap for drain hose, if required ¦ Waste tee for house plumbing, if applicable ¦ Electrical cable or power cord ¦ Screw-type hose clamps ¦ Strain relief for electrical connection ¦ Hand shut-off valve (recommended) ¦ Water line–3/8" minimum copper tubing ¦ GPF10L drain hose (10' long), if needed Junction Box Cover GPF65 Side-Mount Bracket Kit #8 Phillips Special Head Screws 5/8" long Screw Kit #10 Hex-Head J-Box Screw 1/2" long Optional 10' Drain Hose GPF10L Zip Ties Hose Clamps #8 Phillips Pan-head Screws 3/8" long for side-mounting Side- Mounting Brackets Side Mount Kit (some models) Waste Tee Electrical Cable (or Power Cord, if applicable) Wire Nuts (3) Installation Preparation PREPARE DISHWASHER ENCLOSURE 24" Min. This Wall Area must be Free of Pipes or wires Plumbing and Electric Service Must Enter Inside This Area 4" 24" Min. 6" 5" 5"4" Cabinets Square and Plumb Floor MUST be Even With Room Floor. +34-1/2" 1/4" Underside of Countertop to Floor Figure A WARNING: To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. ADVERTENCIA: Para reducir el riesgo de descarga electrica, incendio o lesiones a personas, el instalador debe asegurarse de que el lavaplatos este completamente cerrado en el momento de la instalacion. • The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop. • The dishwasher must be installed so that drain hose is no more than 10' in length for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure. CLEARANCES: When installed into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 28-3/8" min. clearance from the front of the dishwasher for door opening. Figure B. Figure B Clearance for Door Opening 2" Minimum Countertop Dishwasher 28-3/8" DRAIN REQUIREMENTS • Follow local codes and ordinances. • Do not exceed 10' distance to drain. NOTE: Air gap must be used, if waste tee or disposer connection is less than 18" above floor to prevent siphoning. DETERMINE DRAIN METHOD The type of drain installation depends on the following ...