Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
To unlock the dishwasher after it has been locked, touch the LOCK pad twice within 3 seconds. The light above the LOCK pad will turn off. DELAY HOURS Delays the start of a wash cycle for up to 8 hours. (on some models) RESET Touch RESET to cancel options. (timer models) START/RESET Touch START/RESET one time to start dishwasher cycle. Touch START/RESET a second time to pump out (electronic models) and then turn off the dishwasher. Do not touch START/RESET more than one time unless you intend to end the cycle. 6 GEAppliances.com Control Settings Cycle Chart Models Cycle Water Usage (gal.) Cycle Time (min.) Timer Models Hot Start Option1 Heavy Wash Pots & Pans Normal Wash* Light Wash/Water Saver Rinse Only Plate Warmer/Drying 2.5 7.0 7.0 5.6 4.5 2.2 0.0 10 120 118 110 114 58 45 Electronic Models Pots & Pans Heavy Wash Normal Wash China/Crystal Rinse Only 8.8 7.5 5.6 6.3 1.3 112 108 95 80 5 1Hot Start Option adds water amount and cycle time shown when selected. *Normal Wash button should be pushed to run this cycle. NOTE: Not all models have every cycle listed. ConsumerSupportTroubleshootingTipsOperatingInstructionsSafetyInstructions 7 OperatingInstructionsSafetyInstructionsConsumerSupportTroubleshootingTipsOperatingInstructionsSafetyInstructionsConsumerSupport TroubleshootingTips About the dishwasher control panel You can locate your model number on the left tub wall just inside the door. Throughout this manual, features and appearance may vary from your model. Please match the control panel for your unit to a similar control panel below. 8 Operation of models with cycle dial GEAppliances.com Rinse Only For rinsing partial loads that will be washed later. Do not use detergent. Make sure HEATED DRY is not selected. Slowly turn the Dial to RINSE ONLY. 13 Be sure the door is unlatched. 4 Latch the door to start the cycle. 2 Plate Warmer or Drying For warming clean dishes and serving plates. This cycle will take approximately 39 minutes. Load clean dishware to be warmed. 1 Slowly turn the Dial to PLATE WARMER or Select HEATED DRY ON. 4 DRYING. 2 Be sure the door is unlatched. 35 Latch the door to start the cycle. Hot Start or Hot Prestart Option Preheats wash water. Select the HOT STARTor HOT PRESTART Slowly turn the Dial to HOT START or 13 cycle and any other option on the push HOT PRESTART. button pad. 4 Latch the door to start the cycle. Be sure the door is unlatched. 2 Short Wash or Light Wash or Water Saver For quickly washing loads of everyday dishes with light to medium soils that have not dried on. Be sure the door is unlatched. 3 Latch the door to start the cycle. 1 Slowly turn the Dial to SHORT WASH, 2 LIGHT WASH or WATER SAVER. Start (Models with a Dial) Slowly turn the Dial to the START or ON position, or the selected cycle. Don’t turn it past the START, ON or cycle position; you could accidentally miss a prewash. There is a time delay between start-up and water fill so you will not hear any wash action right away. ¦ Latch the door to begin the cycle. 9 ConsumerSupportTroubleshootingTipsOperatingInstructionsSafetyInstructions OperatingInstructionsSafetyInstructionsConsumerSupportTroubleshootingTipsOperatingInstructionsSafetyInstructionsConsumerSupport TroubleshootingTips Operation of electronic models (model GSD4000 Only) Using the Dishwasher Door The door must be closed and locked into place to select a LOAD SELECTION or an OPTION. 1 If the door is opened during a cycle and left open, the dishwasher will beep once every 30 seconds until the 2 door is closed and latched into place. Start Close and latch the door. Touch the START/RESET pad to begin the cycle. Water fill begins and approximately 60 seconds later the wash action begins. NOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher is loaded and the door latch is in the locked position, the control panel lights will be ON and display the last settings you selected. If you don’t want to change any of the settings, simply touch the START/RESET pad to begin the cycle. Also, if a power failure occurs, NORMAL and HEATED DRY will automatically be programmed. Make any new selections and touch the START/RESET pad to begin the cycle. Clean This light is illuminated when a wash cycle is complete. The light will stay ON until the door is opened. Flashing Display Lights Lights What It Means What To Do RESETSTSTARARTTSTART This is normal. Allow the dishwasher to drain and reset before you start a new The START/RESET pad wash cycle. has been pressed. CLEANLEANCCLEAN Control Error Press the START/RESET pad to turn off the beeper. If the CLEAN light continues to flash, call for service. PLUS A BEEPING SOUND Control Error Press the START/RESET pad to turn off the beeper and the dishwasher will attempt to reset. Restart the wash cycle. If this error continues, turn off the power to the dishwasher at the circuit breaker for 30 seconds. Try the dishwasher again. If the error is still present, call for service. P...