Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
When you then use separate detergents again, you should fill the salt and rinse aid compartments, adjust the water hardness setting to the maximum and run an empty wash, then adjust the water hardness setting and the rinse aid setting to the appropriate level. Salt To ensure the best efficiency, the dishwasher needs soft water. Hard water means that lime residues remain on the dishes and the interior of the dishwasher, affecting performance. The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance. This is achieved by using dishwasher salt. To add dishwasher salt, follow the steps below: 1. Remove the lower dishwasher basket and then unscrew the salt compartment cap, as shown in figure 2. 2. Fill the compartment with dishwasher salt (do not use table salt), carefully to prevent unnecessary spillage. Before first use, you should fill the compartment with 2kg of dishwasher salt and then fill up the salt compartment with water (up to the brim of the compartment) as shown in figure 3. 3. Replace the cap and the lower basket. When the salt warning light on the control panel illuminates, you should refill the salt compartment with salt only – do not add water to the salt compartment after the first use. You should run a programme immediately after adding dishwasher salt, to prevent any damage to the dishwasher systems. fig. 2 fig. 1 fig. 3 Softener adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board. 1.Open the testing strip. 2. Run water through the tap for one minute. 3. Hold the testing strip in water for one second. 4. Shake the testing strip after taking it out of the water 5. Wait for one minute 6. Check the number of marks on the strip to see the level of water hardness. If the hardness of the water you use is above 60 dE or if you are using well water; you are recommended to use filter andwater refinement devices. Please note: The level of water hardness is preset to level 3. 1. Press and hold down the programme selection button 2. Press the power button to switch on the dishwasher 3. Keep the programme selection button pressed until the five programme indicator lights and the end of programme indicator light flash. 4. To adjust the level, press the programme selection button until the required level is selected. The programme lights will illuminate as in the table of water hardness settings. 5. To store the selected water hardness level, press the power button. NoLimeVerylowlimecontentLowlimecontentMediumlimecontentLimecontentHighLimecontentIf the hardness of the water you use is above 63dE or if you are using well water; you are recommended to use filter and water refinement devices. Softener adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board. 1.Open the testing strip. 2. Run water through the tap for one minute. 3. Hold the testing strip in water for one second. 4. Shake the testing strip after taking it out of the water 5. Wait for one minute 6. Check the number of marks on the strip to see the level of water hardness. If the hardness of the water you use is above 60 dE or if you are using well water; you are recommended to use filter andwater refinement devices. Please note: The level of water hardness is preset to level 3. 1. Press and hold down the programme selection button 2. Press the power button to switch on the dishwasher 3. Keep the programme selection button pressed until the five programme indicator lights and the end of programme indicator light flash. 4. To adjust the level, press the programme selection button until the required level is selected. The programme lights will illuminate as in the table of water hardness settings. 5. To store the selected water hardness level, press the power button. NoLimeVerylowlimecontentLowlimecontentMediumlimecontentLimecontentHighLimecontentIf the hardness of the water you use is above 63dE or if you are using well water; you are recommended to use filter and water refinement devices. Rinse Aid To fill the rinse aid compartment 1. Open the rinse aid compartment by turning and removing the cap as shown in figure 4. 2. Fill the rinse aid compartment until the rinse aid indicator goes dark, as shown in figure 5 (where “a” indicates the compartment is empty, and “b” indicates the com...
Эта инструкция также подходит к моделям:Посудомоечные машины - WC140 (2.01 mb)
Посудомоечные машины - WC140 (2.01 mb)