Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
It is more economical to always wash with a full load. • Select the wash programme to suit the nature and degree of the soiling on the dishes. • Do not use more detergent, special salt or rinse aid than is recommended in these operating instructions and by the detergent manufacturer. Operating Instructions 8 Appliance Features, Display and Control Panel Spray Arms Display and Control Panel Container for Special Salt Rating plate Container for Rinse Aid Detergent Dispenser Filters Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Spray Arm Water Hardness Switch Operating Instructions Display and control panel Function buttons Control indicator ON/OFF button for Special Salt 123 Indicator for the End of the Wash Programme Function buttons: In addition to the dishwashing cycle the following functions can also be set with the help of these buttons: Function button 1 Set water softener Function button 2 - not programmed Function button 3 Activate/deactivate acoustic signal The control indicator has the following meaning: Refill special salt J 3 The control indicator is never illuminated while a dishwashing cycle is running. Prior to using for the first time Prior to using for the first time, remove all the clips with which the baskets are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid Operating Instructions Water softener To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. The dishwasher therefore has a built-in water softener, in which tap water with a hardness of 4°d (German degree) and harder is softened with the aid of special salt. 3 Your water supplier will be able to inform you about the hardness and hardness range of the water in your area. The water softener can be set manually using the water hardness switch; it can also be set electronically using the buttons on the control panel. Adjusting the hardness Number of Water hardness setting flashes and acoustic signals 1 Range Manually Electronically In °d 2 In mmol/l 3 51 - 70 9,0 - 12,5 10 43 - 50 10 4 7,6 - 8,9 9 37 - 42 9 1 6,5 - 7,5 IV 8 29 - 36 8 5,1 - 6,4 7 23 - 28 7 4,0 - 5,0 6 6 19 - 22 3,3 - 3,9 5 5 III 15 - 18 2,6 - 3,2 4* 4 11 - 14 1,9 - 2,5 II 3 3 0* 4 - 10 0,7 - 1,8 I/II 2 2 1 under 4 under 0.7 I no salt 1 necessary 1) The water hardness will only be indicated acoustically if the acoustic signal has been activated. 2) (°d) German degree, measure of the hardness of water 3) [mmol/l] millimol per litre, international unit for the hardness of water 4) On this setting the length of the dishwashing cycle may be slightly longer. *) Factory setting Operating Instructions Setting the water softener Using the table as a guide, adjust th responds to the hardness of the 0 The dishwasher must be switched off. Setting manually: 1. Open the dishwasher door. 2. Remove the lower rack from the dishwasher. 3. Turn the hardness range switch to or 1 (see table). 4. Replace the lower rack. Setting electronically: 5. Press the ON/OFF button. The LED indicators for all the buttons in the control panel that able to be selected will become illuminated. 3 If the only LED indicator illuminated is one that belongs to a programme button, this means that this dishwashing cycle has been activated. The dishwashing cycle must be cancelled (RESET): Press function buttons 2 and 3 simultaneously for approx.1 second. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 6. Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators for function buttons 1 to 3 will flash. 7. Press function button 1. The LED indicator for function button 1 will flash. The LED indicator for the end of the dishwashing cycle is flashing and acoustic signals can be heard simultaneously (only when the acoustic signal has been activated): – The number of times that the LED indicator for the end of the cycle flashes and the number of acoustic signals correspond to the new hardness setting. – This sequence of flashes and acoustic signals is repeated many times, with a 5 second pause in between. 8. Pressing function button 1 increases the hardness setting by 1. (Exception: hardness setting 1 follows hardness setting 10). 9. When the hardness setting is correct, press the ON/OFF switch. The hardness setting is now saved. 11 Operating Instructions Special salt for the water softener 3 If the water hardness in your area is less than 4 °d, then the water in your dishwasher does not need to be softened and you do not need to use special salt or salt substitute. Water can be softened in one of two ways: • If you are using dishwasher detergent that already contains salt substitute, the detergent only is put into the detergent compartment. – In this case the water softener must manually be set to 0 and electronically t...