Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
· Hygiene * The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. § Half load * If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. . Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 1 Operating the appliance Programme data The programme data (consumption values) can be found in the summary of instructions. This data refers to normal conditions and the water hardness set value 2. Different influencing factors such as water temperature or mains pressure may result in deviations. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Operating the appliance en Switching on the appliance 1. Turn on the tap fully. 2. Open the door. 3. Switch on ON/OFF switch (. The Eco 50° programme display flashes. This programme remains selected unless another programme is selected with the button < H or button > P. 4. Press the START button h. 5. Close the door. The programme starts running. Note -for environmentally friendly operation of the dishwasher: For ecological reasons the Eco 50° programme is preset whenever the appliance starts. This conserves environmental resources and not least saves you money. The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils. en Operating the appliance Optical display while the programme is running * * depending on model While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. 1. Switch on ON/OFF switch (. 2. Keep pressing the Preselected starting time button 0 until the appropriate display 3h, 6h or 9h is lit. 3. Press START button h, timer programming is activated. 4. To delete the preselected starting time, keep pressing the Preselected starting time button 0 until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when neither of the two displays ` or X is lit. The end of the programme is also indicated by an acoustic signal. The buzzer volume can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. This function can be changed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down button > P and press START button h until the dry display ` and salt refill indicator )* flash. 4. Release buttons. 5. Keep pressing button > P until the salt refill indicator )* and rinse aid refill indicator )" flash. 6. Release buttons. The refill indicators )* and )" flash and the displays # and + are lit (= Setting 2). The set buzzer volume can be heard. To change the setting: 1. Press the button < H until the required setting has been selected. 2. Press START button h. The displays go out. The selected setting is saved. 3. Close the door. Note To save energy, the dishwasher automatically switches off after the end of the programme. Interrupting the programme 1. Open the door. 2. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 3. To continue the programme, switch on the ON/OFF switch ( again. 4. Close the door. Operating the appliance en Terminating the programme (Reset) 1. Open the door. 2. Press START button h for approx. 3 sec. until all displays go out. 3. Close the door. The remaining programme sequence for draining the residual water t...
Эта инструкция также подходит к моделям:Посудомоечные машины - DRV4303/11 (1.33 mb)
Посудомоечные машины - DRV4303/14 (1.33 mb)
Посудомоечные машины - DRV4303/15 (1.33 mb)