Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
C (Mar. 2000) Operation and Care of FT900 SERIES DISHWASHERS SAVE THESE INSTRUCTIONS OPERATION MACHINE PREPARATION — Check before beginning operation. Raise the machine doors and make sure all components are in their proper operating positions. Pump Intake Screens must be put on Strainer Pans must be in place on top of Strainer Baskets must be in place in holders at each pump intake (Fig. 1). each tank (Fig. 2). Strainer Pans (Fig. 3). Fig. 1 Fig. 2 End Caps must be correctly installed at Wash Arms must be properly installed ends of all Wash Arms (Fig. 4). and latched in place (Fig. 5). The Final Rinse Arm must be properly Final Rinse Actuators must move freely, installed (Fig. 7). if so equipped (Fig. 8). Fig. 4 Fig. 5 Fig. 7 Fig. 8 Fig. 3 The Flush Arm at load end must be properly installed (Fig. 6). Fig. 6 Curtains must be in their proper places (Fig. 30, pages 9-11) . . . A Short Curtain on the unload side of each upper Prewash, Wash, and Power Rinse Arm, Long Curtains on both sides of every section divider, Two Long Curtains at the Load End. – 2 – © HOBART CORPORATION, 1998 FILL Assure proper water hardness. Recommended range is 4 – 6 grains per gallon. POWER ON / OFF START DOORS CLOSED STOP INITIAL FILL GREENAMBERLight GREENLight Only Fig. 9-a All water (and steam, if equipped) supply valves must be opened and the electric supply turned on before the machine will function. Close the drains and doors. Push the POWER ON / OFF switch (Fig. 9-a). The DOORS CLOSED indicator light (blue) will be lit when all doors are closed. All tanks will fill (for 10 – 15 minutes). When all tanks are filled, the water will automatically shut off and the green INITIAL FILL light will be lit. The proper water level will be BLUELight Only RED maintained throughout operation by the full-time auto-fill feature. On machines equipped with Electric Blower-Dryer option, some were equipped with a lighted BLOWER ON / OFF switch which controls power to the Blower-Dryer (Fig. 9-b) and indicates when the Blower- Dryer is running. NOTE: A RED light (Fig. 9-b) is provided on Blower-Dryers equipped with electric heat to alert the operator to TURN MACHINE OFF, DISCONNECT ELECTRIC POWER, AND HAVE UNIT SERVICED BY A QUALIFIED TECHNICIAN if the blower over-temperature thermostat has been activated. On machines equipped with Steam Blower-Dryer option, some were equipped with a lighted BLOWER ON switch which controls power to the Blower-Dryer (Fig. 9-c) and indicates when the Blower-Dryer is running. When the combination Blower-Dryer switch and indicator light is not provided, the steam Blower-Dryer is on when the pumps are on. Push the green START switch at either end of the machine or at the control box — to start the conveyor and pumps. Push the red STOP switch at either end of the machine or at the control box to stop the conveyor and pumps. Tanks will continue to heat if the POWER ON / OFF switch remains ON. If a separate switch is provided for a Blower-Dryer, push once for On and a second time for OFF. If no separate Blower-Dryer switch is present, the Blower-Dryer should be ON when the pumps are on. Electric Blower-Dryer —Electric Blower-Dryer — Steam Blower-Dryer — Steam Blower-Dryer — with ON / OFF Switch without ON / OFF Switch with ON / OFF Switch powered by the machine and Red Indicator Light with Red Indicator Light ON / OFF switch BLOWER ON / OFF WHITELight REDLight Only ! WARNING If red indicator lights: • Disconnect from power supply • Have unit serviced by qualified technician REDLight Only ! WARNING If red indicator lights: • Disconnect from power supply • Have unit serviced by qualified technician BLOWER ON WHITELight Fig. 9-c Fig. 9-b DISHWASHING To start the conveyor, pumps, and blower-dryer (if not switched separately), press the green START switch at either end of the machine or at the control box. The conveyor will operate only when all machine doors are closed and the tanks are filled to the proper level. When equipped with Blower- Dryer, the Blower-Dryer will operate with the conveyor and pumps. Press the red STOP switch at either end of the machine or at the control box to stop the conveyor and pumps. The Auto-Timer will automatically stop the machine if no ware is washed for a preset length of time. The Auto-Timer shutoff setting can be changed by your Hobart service technician (range is 2 – 8 minutes). – 3 – Empty Strainer Baskets During Operation as Necessary The Strainer Baskets must be emptied periodically during operation to prevent them from becoming clogged, which would adversely affect dishwasher operation. STOP the machine and open the side access doors; Strainer Baskets are immediately inside at the front of the tanks. Loading Pre-scrap dishes thoroughly to remove large food particles and debris. Never use steel wool on ware to be loaded into the dishwashing machine. All plates, saucers, trays, etc. should be loaded on the conveyor in an inclined position. Bowls should be loaded upside down. Cups, glasses,...