Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
There is a slight increase in the energy consumption. Washing the dishes Programme data The programme data (consumption values) can be found in the summary of instructions. This data refers to normal conditions and the water hardness set value 2. Different influencing factors such as water temperature or mains pressure may result in deviations. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Switch on ON/OFF switch (. The display of the last selected programme flashes. This programme remains selected unless another programme is selected with the button < H or button > P. – Press the START button h. – Close the door. The programme starts running. en Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. – Switch on ON/OFF switch (. – Keep pressing the Preselected starting time button 0 until the appropriate display 3h, 6h or 9h is lit. – Press START button h, timer programming is activated. – To delete the preselected starting time, keep pressing the Preselected starting time button 0 until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the End display ` is lit. The end of the programme is also indicated by an acoustic signal. The buzzer volume can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Release buttons. – Keep pressing button > P until the salt refill indicator )* and rinse aid refill indicator )" flash. – Release buttons. The refill indicators )* and )" flash and the displays # and + are lit (= Setting 2). The set buzzer volume can be heard. To change the setting, – Press the button < H until the required setting has been selected. – Press START button h. The displays go out. The selected setting is saved. – Close the door. Switching off the appliance Short time after the end of the programme: – Open the door. – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Open the door. – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. – Close the door. Terminating the programme (Reset) – Open the door. – Press START button h for approx. 3 sec. The Cleaning display X goes out. – Close the door. The remaining programme sequence lasts approx. 1 minute more. (Buzzer sounds.) – Open the door. – Switch off ON/OFF switch (. – Close the door. en Changing the programme When the START button h has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Open the door. – Switch on ON/OFF switch (. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Release buttons. – Keep pressing button > P until the salt refill indicator )* and “Check water supply” )2 flash. – Release buttons. The displays )* and )2 flash. To change the setting, – Press button < H until the display # is lit (Intensive drying on). – Press START button h. The displays go out. The setting is saved. – Close the door. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temp...
Эта инструкция также подходит к моделям:Посудомоечные машины - S52E50X1GB/21 (1.78 mb)
Посудомоечные машины - S52E50X1GB/25 (1.78 mb)
Посудомоечные машины - S52E50X1GB/28 (1.78 mb)