Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Large Little Very little Very adhesive Medium Lightly Adhesive Intensive 70. Auto 55-65. Eco 50. Gentle 40. Quick 45. Prerinse Wash programme Programme- sequence Clean 70. Clean 70 Prerinse 40 Inter- mediate rinse Clean 40 Prerinse Clean 45 Dry Clean 55 Clean 55 Dry Clean 65 Clean 50 Prerinse Dry Dry The programme sequence isoptimised and adjusted accordingto the degree of soiling on theutensils. Prerinse Intermediate rinse Intermediate rinse Intermediate rinse Programme selection amount and condition of food remains, with the details contained in the The most appropriate programme can be programme overview. identified by comparing the type of You will find the appropriate programme crockery, cutlery, etc., as well as the information in the introduction. en Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The programme specifications can be found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. A light barrier can detect dissolved food remnants in the water, e.g. egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 9 is pressed. The numerical display 3 shows the expected duration of the programme. The programme starts automatically. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. Time delay * * on applicable models You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button 4 until the digital display 3 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when a figure appears in the numerical display 3 . en Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. Interrupting the programme Set main switch 1 to OFF. Indicator lights extinguish. The programme is retained in the dishwasher memory. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. In order to continue with the stored programme, set the main switch to ON again. Cancel programme (Reset) Only when the master switch is ON. Press the A and C buttons simultaneously, and hold them pressed for approx. 3 seconds. The numerical display shows . The programme continues for approx. 1 min. When it has ended, set the main switch 1 to OFF. To restart the dishwasher, set main switch 1 to ON again and select desired programme. Changing the programme It is possible to change the programme within 2 minutes after you ...
Эта инструкция также подходит к моделям:Посудомоечные машины - S44M45N3GB/73 (2.51 mb)
Посудомоечные машины - S44M45N5GB/01 (2.51 mb)
Посудомоечные машины - S44M45N5GB/82 (2.51 mb)
Посудомоечные машины - S44M45N5GB/90 (2.51 mb)