Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Switch on main switch 1 and hold down for at least 3 sec. The digital display 8 indicates the current set hardness value and the salt refill indicator 6 flashes (hardness value has been set to 4 at the factory). To change the setting: Rotate the programme selector 3 . You can select a set value between 0 and 7 according to the hardness of your water. Switch off the main switch 1 . The chosen setting has now been stored. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Coffee, cake, milk, sausage, cold drinks, salads Soups, souffles, potatoes, pastries, rice, eggs, fried food Delicate Type of Dishes e.g. porcelain, pans, cutlery, glasses, etc. Type of food remnants e.g. Programme- sequence Dry Clean 55 Clean 40 Prerinse Clean 55 Clean 45 Soups, potatoes, pastries, rice, eggs, fried food Wash programme Very little Amount of food remnants State of food remnant Intensive 70 Eco 50 Gentle 40 Quick 45 Prerinse Mixed Dry Clean 65 Clean 50 Prerinse Dry Clean 70 Clean 70 Prerinse 40 Prerinse Rinse off if the dishes have been stacked for several days in the dishwash er prior to washing. Inter- mediate rinse Inter- mediate rinse Inter- mediate rinse Inter- mediate rinse LittleLarge MixedNon- sensitive Lightly AdhesiveVery adhesive Dry Clean 70 Inter- mediate rinse Clean 65 Prerinse Inter- mediate rinse Normal 65 en Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme specifications The programme specifications can be found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to: varying amounts of dishes water supply temperature water pipe pressure ambient temperature mains voltage tolerances and the tolerances specific to the appliance (e.g. temperature, amount of water, etc.) The water consumption values refer to a set water hardness value of 4. Aqua sensor * * some models The Aquasensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way water consumption can be reduced by approx. 4 litres. Switching on the appliance Close the door. Turn on the tap fully. Rotate programme selector 3 to the required programme. Switch on the main switch 1 . The expected programme duration is indicated on the numerical display 8 . The programme sequence starts automatically. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. End of programme The programme has ended when a figure appears in the numerical display 8 . en Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme Switch off the main switch 1 . The lit display goes out. The programme is saved. If there is a warm water connection or if the machine has already heated up and the appliance door was opened, leave the door open for several minutes and then close. Otherwise, expansion may cause the appliance door to spring open. Switch on the main switch again. Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. The digital display indicates after approx. 3 sec. The programme sequence lasts approx. 1 min. When the programme has run, switch off the main switch 1 . To restart...
Эта инструкция также подходит к моделям:Посудомоечные машины - S44E55W1EU/01 (2.36 mb)