Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Onboard computer You can switch the onboard computer (additional programme information) off or on. Proceed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button h until s:‹... is indicated on the digital display 8. 4. Release both buttons. 5. Press programme button # until the factory set value ’:‹‹ is indicated on the digital display 8. To change the setting: 1. By pressing the 3 button, you can switch the on board computer (additional programme information) off ’:‹‹ or on ’:‹‚. 2. Press START button h. The set value is saved. 3. Close the door. Timer programming You can delay the start of the programme in 1 hour steps up to 24 hours. 1. Open the door. 2. Switch on ON/OFF switch (. 3. Press the button X + until ‹‚ is flaching in the timer programming display P. 4. Press + or – button until the X displayed time corresponds with your requirements. 5. Press START button h, timer programming is activated. Operating the appliance aus 6. To delete timer programming X, press the + or – button until ‹‹ is indicated on the digital display P. You can change your programme selection at any time until the programme starts. 7. Close the door. End of programme The programme ends when the value ‹:‹‹ appears on the digital display 8 and Finished appears in the display window )*. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button h until s:‹.... is indicated on the digital display. 4. Release both buttons. 5. Press programme button # until the factory set value ›:‹. is indicated on the digital display 8. To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). 2. Press START button h, the set value is saved. 3. Close the door. aus Operating the appliance Automatic switch off after end of programme or interior light* * depending on model To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends. The setting can be selected from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically. The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for longer than 60 min., the light switches off automatically. The interior light 1" is lit only when the set value .:‹‹ is selected. .:‹‚ Appliance switches off after 1 min. .:‹. Appliance switches off after 120 min. 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button h until s:‹... is indicated on the digital display. 4. Release both buttons. 5. Keep pressing programme button # until the value .:‹... is indicated on the numerical display 8. To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹. 2. Press START button h. The set value is saved. 3. Close the door. Switching off the appliance Short time after the end of the programme: 1. Open the door. 2. Switch off ON/OFF switch (. 3. Turn off the tap (not applicable if Aqua-Stop fitted). 4. Remove the utensils when they have cooled down. Note When the programme ends, leave the appliance to cool down a while before opening it. This will prevent steam from escaping and causing long- term damage to your built-in furniture. Interrupting the programme 1. Open the door. 2. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 3. To continue the programme, switch on the ON/OFF switch ( again. 4. Close the door. Terminating the programme (Reset) 1. Open the door. 2. Press START button h for approx. 3 sec. The digital display 8 shows: ‹:‹‚, the display window )* indicates: Program was terminated, Ready in 1 minute. 3. Close the door. The programme sequence lasts approx. 1 min. The digital display 8 shows: ‹:‹‹, the display window )* indicates: Finished. 4. Open the door. 5. Switch off ON/OFF switch (. 6. Close the door. Changing the programme When the START button h has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START bu...
Эта инструкция также подходит к моделям:Посудомоечные машины - SMS69T28AU/73 (2.19 mb)