Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
“d:01” = ON and “d:00” = OFF 6 Press [Start] to save setting and close the door. Auto Power Off To save energy, the dishwasher is turned off 1 minute after the wash cycle ends. Auto Power Off can be adjusted from P:00 to P:02. To change the factory setting (P:01): 1 Open the door and press the [On/Off] button. 2 Hold down the “A” button and press [Start] until the display indicates “H:00”. 3 Release both buttons. 4 Press the “A” button until the display indicates “P:01”. 5 Press the “C” button until the display corresponds with your requirements. P:00 = dishwasher does not turn off automatically P:01 = dishwasher turns off automatically after 1 minute P:02 = dishwasher turns off automatically after 120 minutes (2 hours) 6 Press [Start] to save the setting and close the door. InfoLight An LED illuminates the floor to indicate the unit is running. If the appliance is installed at eye-level, the LED is not visible. To change the setting: 1 Open the door and press the [On/Off] button. 2 Hold down the “A” button (see page 4) and press [Start] until the display indicates “H:00”. 3 Release both buttons. 4 Press the “A” button until the display shows “1:01”. 5 Press the “C” button to switch between “1:01” = ON and “1:00” = OFF 6 Press [Start] to save and close the door. Care and Maintenance A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents future problems. Overall condition of the machine Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance with a damp cloth - water and a small amount of liquid soap is adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths. Clean the outer edges of the inside door panel regularly to remove debris that may collect from normal loading. If spots begin to appear on the stainless steel, make sure the rinse agent is full and functioning properly. Filters The filter system consists of a coarse filter, a flat fine filter and a micro filter. The filters keep large foreign objects in the rinsing water away from the pump. Foreign objects may occasionally block the filters. Check the filters for residue by: • Unscrew the filter cylinder as illustrated in Figure 10-11 and take out the filter system. • Remove any residue and clean filters under running water. • Reinstall filter system in reverse sequence and ensure that the arrow marks are facing each other after locking it into place. Spray Arms Check spray arms for grease and limescale deposits. If you find such deposits: • Fill detergent dispenser with detergent and start the appliance without utensils in the cycle with the highest rinsing temperature (see wash cycle information table). • Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. • Unscrew the spray arms and inspect as shown in Figure 12. Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. the rinsing water does not get pumped out and covers the filters. In this case: • Disconnect the appliance from the power supply. • Remove the filters. • Scoop out standing water - use a sponge if necessary. • Using a spoon, pry off the pump cover (see Figure 13-14) until it clicks, then grip the cover and pull upward until it resists and then pull forward. • Check inner compartment and remove any foreign objects. • Place cover in the original position, press down and engage. • Reinstall filters. Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 1 2 1 2 3 Click Self Help Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following information may help you with a dishwasher problem without involving a repair professional. Problem Cause Action Dishwasher does not start 1. Door may not be properly latched 2. Unit may not be turned on 3. Unit not reset or previous cycle not completed 4. Delay start engaged 5. Interruption of electrical power supply to dishwasher or blown fuse. 6. The door may have been closed without first selecting a cycle 7. Water supply may not be turned on 1. Shut the door completely 2. Press the main power switch to turn unit on 3. To reset, refer to “cancelling or changing cycle” in this manual 4. To reset, refer to “delay start” section in this manual 5. Check circuit breaker 6. Select a cycle and close the door. 7. Check and turn on water supply Dishwasher 1. Default factory settings alert the customer that 1. To adjust the volume or deactivate, refer to the beeping (end the cycle is complete by beeping. This feature can “cycle completion signal” section in this manual. of cycle sigbe deactivated if so desired. nal) Display does 1. A fuse may have been blown or circuit breaker 1. Check the fuse or circ...
Эта инструкция также подходит к моделям:Посудомоечные машины - SGV63E03UC/73 (2.17 mb)