Greater deviations may be caused by: different quantities of utensils inlet temperature of the water water pressure ambient temperature mains voltage tolerances and appliance-specific tolerances (e.g. temperature, water flow rate, etc.) Only ranges can be indicated for the automatic programmes. The water consumption values refer to water hardness value 4. Selecting options/ standard settings Operating principle Auto Wash Options Start The following options / standard settings can be selected in turn from the main menu by repeatedly pressing the “Options” button : Timer programming Reduce time Degree of dryness Buzzer volume Water hardness Rinse aid dosage Language Standard programmes One option / standard setting contains several settings which can be selected with the or buttons. The selected setting is saved by jumping to the next option / standard setting (button ) (exception: standard programmes) or by returning to the main menu (button ). en Timer programming You can delay the start of the programme by up to 24 hours in hour steps. If the Timer programming option is selected, “Delay start 0:00 hrs” is displayed. Select the desired time. Return to the main menu and start the selected programme. Close the door. The time begins to count down. To interrupt or check the countdown, open the door. When the set time has elapsed, the programme starts automatically. Until the programme starts you can change the set time and selected programme. Return to the main menu by pressing the “Back” button and change the settings. Finally, restart the programme. To delete Timer programming, reset the time to 0:00. Reduce time You can reduce the running time of automatic programmes. An optimum cleaning result is still obtained as both the water and energy consumption is increased. If the Reduce time option is selected, “Reduce time: Off” (factory setting) is displayed. Select “Reduce time: On”. Return to the main menu and start the selected programme. If you do not want to use Reduce time the next time you use the dishwasher, you must switch off the option again. Degree of drying If the “Degree of drying” option is selected, “Normal drying” is displayed (factory setting). Alternatively, you can select “No drying” or “Extra drying”. The temperature of the final rinse is increased in all programmes for “Extra drying”. (Note the higher temperature may not be suitable for fragile utensils.) Buzzer volume You can vary the volume of the buzzer or switch it off completely. If the Buzzer volume option is selected, “Buzzer 4” is displayed (factory setting). You can select value 0 (buzzer switched off) or values from 1 (quiet) to 6 (loud). Buzzer is emitted briefly, indicating the volume which corresponds to the value just selected. Water hardness Before using the appliance for the first time or if the water hardness changes, the dishwasher softening system must be adjusted to the degree of hardness of your tap water. Proceed as described in the chapter “Adjusting the softening system”. Rinse aid dosage You can adjust the rinse aid dosage. If the Rinse aid dosage option is selected, “Rinse aid 4” is displayed (factory setting). Do not change this setting unless there are streaks (reduced value) or water stains (increased value) on the utensils. You can select a value between 0 and 6. en Language Before using the appliance for the first time, you can change the selected language (see chapter “Before using the appliance for the first time”). If the Language option is selected, several language codes are displayed. The code of the currently selected language flashes. A total of 17 codes or languages can be selected. If selecting a language code, the clear text is displayed on the lower line in the corresponding language. Standard programmes In addition to the wash programmes which can be selected from the main menu, the following standard programmes can be selected in turn from the “Normal” programme: Normal Extra – Normal Eco – Normal – Normal Plus. Select the desired programme and return to the main menu. If you do not want to select any of the displayed standard programmes, return to the “Standard programmes” display and then to the main menu by pressing the “Back” button . If you would like to cancel the selection of a standard programme, select the Standard programmes option. Then simultaneously press the “Main menu” button and button or button . The selected standard programme is then deleted. The main menu and ”Auto Wash” programme are displayed. Type of utensil Normal Extra Normal Eco Normal Normal Plus Mixed utensils Amount of food remains Condition of food remains Small to large Slightly adhesive The associated programme data (duration, energy and water consumption) can be found in the summary of instructions. We strongly recommend that you use the automatic programmes as the energy and water consumption is kept as low as possible on account of the variable programme sequence. However, the programme sequence of the standard ...

Эта инструкция также подходит к моделям:
Посудомоечные машины - SGVKBR2/19 (2.67 mb)
Посудомоечные машины - SGVKBR2/20 (2.67 mb)
Посудомоечные машины - SGVKBR2/21 (2.67 mb)
Посудомоечные машины - SGVKBR2/23 (2.67 mb)