Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Individual positions are referred to in the text. Control panel 1 Main switch 2 Door Opener 3 Programme selector (retractable*) 4 Additional options* 5 “Check water supply” display 6 Salt refill indicator 7 Rinse-aid refill indicator 8 Digital display * some models Appliance interior 20 Upper basket with additional cup rack 21 Additional cutlery basket for the top basket* 22 Top spray arm 23 Bottom spray arm 24 Dispenser for salt 25 Filters 26 Cutlery basket 27 Bottom basket 28 Lock for detergent dispenser 29 Dispenser for rinse aid 30 Detergent dispenser 31 Rating plate * some models You will need to purchase the following before using the dishwasher for the first time: – special salt for use in dishwashers – detergent – rinse-aid Only use products, which are suitable for dishwashers. en Water softener In order to rinse dishes and glasses satisfactorily, the dishwasher requires soft water, i.e. containing little or no lime, otherwise water stains will be left behind on crockery and glasses, etc. If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener Determine the level of hardness of your tap water. Your local water company or service agent can help you with this. Identify setting from the following water hardness table. Water hardness table Close the door Rotate the programme selector 3 from the 12 o’clock position by one notch to the left. Switch on main switch 1 and hold down for at least 3 sec. The digital display 8 indicates the current set hardness value and the salt refill indicator 6 flashes (hardness value has been set to 4 at the factory). To change the setting: Rotate the programme selector 3 . You can select a set value between 0 and 7 according to the hardness of your water. Switch off the main switch 1 . The chosen setting has now been stored. Approx. 4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. en Filling in the Salt Open the screw-type cap of the compartment 24 . Warning Before switching on the appliance for the first time, pour approx. 1 litre of water into the salt dispenser. Then refill with salt (not cooking salt) until the salt container is full (max. 1.5 kg). When you refill the salt, water is being displaced and drains off. Refill with salt always just before switching on the appliance in order to prevent corrosion. As a result, any salt solution which has run over will be immediately diluted and flushed out. Then clean the filling area of salt residues and screw the compartment lid back on without tilting the lid. The LOW SALT indicator 6 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. If the set hardness value is , do not add salt because no salt is used during operation; the salt refill indicator is switched off. Do not pour detergent into the container for special salt. This would destroy the water softener. Salt refill indicator As soon as the salt refill indicator 6 is lit on the control panel, refill with salt immediately before the next rinse cycle. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. en Adding rinse aid The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Open the cover on the rinse-aid dispenser 29 . To do this, press the mark (1 ) on the cover and simultaneously lift the cover on the control plate (2 ). Adjusting the amount of rinse-aid The amount of rinse-aid added to the water can be varied by adjusting the stepless control. The rinse-aid control has been set to ”4” in the factory. Do not alter the setting of the rinse-aid control unless streaks (turn knob towards ”–”) or water marks (turn knob towards ”+”) are left on the dishes. 29 Carefully pour in the rinse aid to just below the edge of the filler opening. Close the lid, ensuring that you hear it snap closed. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Rinse aid controller Rinse-aid refill indicator As soon as the rinse-aid refill indicator lights up on the control panel 7 , refill with rinse aid. If using detergent products with integrated rinse aid, the rinse-aid refill indicator can be switched off (see “Switching the rinse-aid refill indicator off and on” in the “auto 3in1” chapter). en Not suitable for the dishwasher The following should not be cleaned in the dishwasher: Wooden cutlery and utensils – these will ...
Эта инструкция также подходит к моделям:Посудомоечные машины - SGS65E22EU/82 (2.39 mb)
Посудомоечные машины - SGS65E22EU/86 (2.39 mb)
Посудомоечные машины - SGS65E22EU/90 (2.39 mb)