Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Switching on the appliance Close the door. Turn on the tap fully. Rotate programme selector 3 to the required programme. Switch on the main switch 1 . The expected programme duration is indicated on the numerical display 7 . The programme sequence starts automatically. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. End of programme The programme has ended when a figure appears in the numerical display 7 . Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. aus Interrupting the programme Switch off the main switch 1 . The lit display goes out. The programme is saved. If there is a warm water connection or if the machine has already heated up and the appliance door was opened, leave the door open for several minutes and then close. Otherwise, expansion may cause the appliance door to spring open. Switch on the main switch again. Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. The digital display indicates after approx. 3 sec. The programme sequence lasts approx. 1 min. When the programme has run, switch off the main switch 1 . To restart, rotate the programme selector to the required programme. Switch on the main switch 1 . The programme sequence starts automatically. Changing the programme When the appliance is switched on, the programme can be changed within minutes. If the programme is changed subsequently, programme sections (e.g. Cleaning) which have already started run to the end. The new remaining time consists of the remaining time of the previous programme section and the remaining time of the newly selected programme. Intensive drying By activating the “Intensive drying” function, the final rinse will produce a higher temperature in all programmes resulting in an improved drying result (please note that higher temperatures might have an effect on delicate items). Close the door. Hold down button B and switch on main switch 1 . Release both buttons. The digital display 7 indicates (on) or (off) and button B flashes. To change the setting, press button B . Switch off the main switch 1 ; the chosen setting has now been stored. aus Additional functions * on some models additional functions can be set with the buttons. Soaking * The soaking cycle runs before the main programme and must be selected before the programme starts. In this additional programme cooking utensils, e.g. pans, bowls, etc., can be soaked and prerinsed in the bottom basket. It is recommended to put approx. 5 g of detergent on the door. Reduce/save time* The rinsing times and the drying phase are reduced. The reduced time lowers the rinsing and drying performance. Top basket washing only * If there are only a few utensils (e.g. glasses, cups, plates), use the top basket. The bottom basket must be empty! Use slightly less detergent than is recommended for a complete load. Bottom basket washing only * If there are only a few utensils (e.g. plates, pans, bowls), use the bottom basket. The top basket must be empty! Use slightly less detergent than is recommended for a complete load. Time delay * h. You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button until the digital display 7 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. aus Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine Check washing chamber for grease and limescale deposits. If you find such deposits: Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which has the highest wash temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the door seal with a damp cloth. Never use a steam cleaner to clean...
Эта инструкция также подходит к моделям:Посудомоечные машины - SGI55E45AU/76 (2.41 mb)