Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
– Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Switch off the main switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the main switch ( again. Terminating the programme (Reset) – Only when the main switch is on: Rotate programme selector 8 to the Reset position. The digital display ` indicates ‹ after approx. 3 sec. – The programme sequence lasts approx. 1 min. – Switch off the main switch (. Changing the programme After you have switched the appliance on, it is possible to change the programme within 2 min. If you want to change the programme afterwards, the appliance waits until the initiated programme section (e. g. washing) ends. The remaining time comprises the remaining time of the previous programme section and the remaining time of the new selected programme. Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Hold down button + and press main switch ( until the digital display illuminates. – Release both buttons. The factory-set value ‹ (off) or ‚ (on) is lit on the digital display `. To change the setting: – By pressing the button +, you can switch intensive drying on ‚ or off ‹. – Switch off the main switch (. The set value is saved. en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators P and X. If required, refill salt and/or rinse aid. Filters The filters 1J keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. – After each wash cycle check the filters for residue and clean if required. – After unscrewing the coarse microfilter, you can take out the filter group. – Remove any residue and clean filters under running water. – Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. en Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 12 and 1:. – Check outlet nozzles on the spray arms for blockages. – Unscrew the upper spray arm 12. – Remove the lower spray arm 1: upwards. – Clean spray arms under running water. –Re-engage or screw on spray arms. Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to eliminate them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Dishwashing”) a=Warning Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. en Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: – First disconnect the appliance from the power supply. – Remove the filters 1J. – Scoop out water, use a sponge if required. – Loosen screw on the cover (Torx T 20) and remove the cover. – Check inner compartm...
Эта инструкция также подходит к моделям:Посудомоечные машины - SF25M855EU/18 (1.36 mb)