Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Switch on ON/OFF switch (. – Rotate programme selector 8 to the required programme. The expected programme duration flashes on the digital display H. – Press START button @. The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display H. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). en Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Close the door. – Switch on ON/OFF switch (. – Press button P until the digital display H jumps to oe:‹‚. – Press button P until the displayed time corresponds with your requirements. – Press START button @, timer programming is activated. – To delete the preselected starting time, press the button P until oe is indicated on the digital display. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display H. Switching off the appliance Short time after the end of the programme: – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) – Press START button @ for approx. 3 sec. The numerical display H indicates ‹:‹‚. – The programme sequence lasts approx. 1 min. On the digital display H is indicated ‹:‹‹. – Switch off ON/OFF switch (. Changing the programme When the START button @ has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). en Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Switch on ON/OFF switch (. – Press and hold down the START button @. – Rotate programme selector 8 until s:‹‹ is indicated on the digital display H. – Release button. The factory-set value s:‹‹ is lit on the digital display H (intensive drying off). Change the setting as follows: – By rotating the programme selector 8, you can switch intensive drying on s:‹‚ or off s:‹‹. – Press START button @. The set value is saved. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators h and `. If required, refill salt and/or rinse aid. en Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. –Remove any residue and clean filters under running water. –Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Spray arms Limescale and contaminants in the...
Эта инструкция также подходит к моделям:Посудомоечные машины - DGS5512/26 (1.74 mb)
Посудомоечные машины - DGS5518/01 (1.74 mb)
Посудомоечные машины - DGS5518/26 (1.74 mb)
Посудомоечные машины - DIS5505/01 (1.74 mb)