Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
• Unscrew ilter cylinder as illustrated and take out ilter system. • Remove any residue and clean ilters under running water. • Re-install ilter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the ilter system. CAUTION To avoid injury, do not reach into the large object trap with your ingers. The large object trap could contain sharp objects. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms. Using the water softening system may reduce this. • Check outlet nozzles on the spray arms for blockages. • Unscrew the upper spray arm. • Remove the lower spray arm. Waste water pump Large food remnants in the rinsing water not retained by the ilters may block the waste water pump. The rinsing water does not get pumped out and covers the ilter. In this case: • Disconnect the appliance from the power supply. • Remove the ilters. • Scoop out water, use a sponge if required. • Using a spoon, pry off pump cover(as illustrated) until it clicks, then grip the cover by the lug and irst pull it upwards until it resists and then pull it out forwards. • Check inner compartment and remove any foreign objects. • Place cover in the original position, press down and engage. • Install ilters 123Klick12 SELF HELP Dishwashers may occasionally exhibit problems that are unrelated to a malfuncion of the dishwasher itself. The following informaion may help you with a dishwasher problem without involving a repair professional. Problem Cause Acion Dishwasher 1. Door may not be properly latched. 1. Shut the door completely. does not start 2. Unit may not be turned on. 3. Unit not reset or previous cycle not completed. 4. Delay start engaged. 5. Interrupion of electrical power supply to dishwasher or blown fuse. 6. Child lock acivated (select models). 7. The door may have been closed without irst selecting a cycle. 8. Water supply may not be turned on. 2. Press the main power switch to turn unit on. 3. To reset, refer to “Canceling or changing the cycle” secion in this manual. 4. To reset, refer to “Delay Start” secion in this manual. 5. Check circuit breaker. 6. Deacivate the child lock. Refer to “Child Lock” secion in this manual if applicable. 7. Select a cycle and close the door. 8. Check and turn on water supply. Dishwasher beeping (end of cycle signal) Default factory seings alert the customer that the cycle has completed by beeping. This feature can be deacivated if so desired. To adjust the volume or deacivate, refer to “Cycle Compleion Signal” secion in this manual. Display does 1. A fuse may have been blown or circuit breaker 1. Check the fuse or circuit breaker box and replace the fuse or re- not illuminate tripped. set the breaker if necessary. or console 2. Door not closed or latched. 2. Ensure that door is properly latched and completely closed. lights are not Note: For models with controls on the top porion of the on door, the display only illuminates when the door is opened and controls are visible. Dishwasher 1. Incoming water is not warm enough. 1. Before staring a cycle, run hot water faucet at the sink nearest seems to run a 2. Cycle ime can vary due to soil and water condito the dishwasher. long ime ions. 3. Rinse agent dispenser is empty. 4. Dishwasher connected to cold water supply. Note: Refer to “Cycle Chart Data” secion in this manual for typical cycle length. 2. Sensors in the dishwasher automaically increase the cycle ime to ensure a good wash when heavy soil is detected. 3. Add rinse agent. 4. Verify dishwasher is connected to hot water supply plumbing. Dishes aren’t 1. Spray arm movement is obstructed. 1. Ensure that spray arm movement is not blocked by hand rotaing geing clean 2. Spray arm nozzles clogged. spray arms. enough 3. Improper use of detergents. 4. Filters could be clogged. 5. Dishes are nested or loaded too close together. 6. Selected wash cycle is not suitable for food soil condions. 2. Remove the spray arms and clean according to “Check/Clean the Spray Arm Nozzles” in Care and Maintenance secion of this manual. 3. Increase or decrease detergent depending on the water hardness. Refer to Table under “Adding Detergent and Rinse Agent”. 4. Clean the ilter. Refer to “Check/Clean the Filter System” under Care and Maintenance secion of this manual. 5. Rearrange load such that water spray can reach all items in the dishwasher. See also “Preparing and Loading” secion of this manual. 6. Refer to “Wash Cycle” secion in Operaing the Dishwasher secion of this manual. Dishes are not 1. Rinse agent dispenser is empty. (Rinse agent indica1. Add rinse agent. The use of rinse agent improves drying. geing dry tor is acivated). 2. Rearrange load to ensure items are not nested. Refer also to the enough 2. Improper loading of dishes. 3. Selected cycle does not include drying. Note: Plasic or Telon do not typically dry as completely as other items due to their inherent properies. “Preparing and Loading” secion of thi...
Эта инструкция также подходит к моделям:Посудомоечные машины - DF261760/55 (7.81 mb)
Посудомоечные машины - DF261760/73 (7.81 mb)