* depending on model Damage – The appliance may be repaired and opened up by a technician only. To do this, disconnect the appliance from the power supply. Pull out the mains plug or switch off the fuse. Turn off the tap. Disposal – Make redundant appliances unusable to prevent subsequent accidents. – Dispose of the appliance in an environmentally friendly manner. a=Warning Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations. Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed. Before using your appliance for the first time Your appliance was tested before it left the factory. To remove any remaining test water, wash the first time without utensils at the highest temperature. Pour salt, rinse aid and detergent into the designated filling orifices. en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel ( Main switch 0 Door opener 8 Timer programming * @ Digital display H Additional options ** P “Tap 6” display * X Salt refill indicator ` Rinse aid refill indicator h Programme buttons ** * depending on model ** Number depending on model Appliance interior 1" Top basket 1* Knife shelf * 12 Top spray arm 1: Etagere * 1B Bottom spray arm 1J Float *** 1R Bottom basket 1Z Dispenser for special salt 1b Filters 1j Cutlery basket 9" Dispenser for rinse aid 9* Detergent dispenser 92 Lock for detergent dispenser 9: Rating plate * depending on model *** The float 1J ensures that the appliance interior is not overfilled. Only customer service may maintain, remove and install the float. en Water hardness table Water softening system To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 9° Clarke (from set value •:‹‚) must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Setting The amount of salt dispensed can be set from ‹ to .. Salt is not required at the set value ‹. – Find out about the hardness value of your tap water. Your water utility company will help you with this. – Set value can be found in the water hardness table. – Open the door. – Hold down programme button + and switch on the main switch (. – Release both buttons. The LED for button + flashes and the digital display @ displays the factory setting …. To change the setting: – Press programme button +. Each time the button is pressed, the set value increases by one level; when the value of . has been reached, the display jumps back to ‹ (off). – Switch off the main switch (. The chosen setting has now been stored. . . . " # . . %. #$ . . ! ! . . . . . . . . en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 1Z. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add salt (not table salt). The water is displaced and runs out. * depending on model The salt refill indicator X on the fascia is lit. It goes out as soon as a sufficiently high salt solution has formed. If the set value ‹ is displayed, do not add any salt because salt will not be used during operation of the appliance, the salt display is switched off. If the set values ‚ to . are displayed, salt must be added. Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. Salt refill indicator As soon as the salt refill indicator X on the fascia is lit, top up the salt. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. If the salt refill indicator X is impaired (e. g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Setting water softening system” and set the value to ‹. The water softening system and salt refill indicator are now switched off. a=Warnings – Never fill the salt dispenser with detergent. You will destroy the water softening system. – To prevent corrosion, always refill with salt immediately before switching on the appliance. en Rinse aid % As soon as the rinse-aid refill indicator ` is lit on the fascia, there is still a rinse-aid rese...

Эта инструкция также подходит к моделям:
Посудомоечные машины - CG446V5/39 (2.11 mb)
Посудомоечные машины - CG447V5/36 (2.11 mb)
Посудомоечные машины - CG447V5/39 (2.11 mb)