Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Bosch, модель CG341J2/21

Производитель: Bosch
Размер: 2.45 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener (see introduction) Filling in the Salt Function of the salt During the rinse cycle the salt is being washed automatically from the salt compartment into the softening system where it will dissolve the lime. The lime-containing solution drains from the dishwasher. Afterwards the softening system is ready to be loaded again. This regeneration cycle will only work if the salt is dissolved in water. Open the screw-type cap of the compartment 27 . Before switching on the appliance for the first time, pour approx. 1 litre of water into the salt dispenser. Then refill with salt (not cooking salt) until the salt container is full (max. 1.5 kg). When you refill the salt, water is being displaced and drains off. Therefore, to prevent corrosion, always refill with salt immediately before switching on the dishwasher. This way the overflowing salt solution is diluted and flushed immediately. Use the enclosed salt filling aid ( in some models). Then clean the filling area of salt residues and screw the compartment lid back on without tilting the lid. en Note If the switch is set to ”0”, it is not necessary to add any salt, as none is consumed while the dishwasher is operating. If the switch is set between ”1” and ”3”, then salt must be added. Do not pour detergent into the container for special salt. This would destroy the water softener. LOW SALT indicator Salt should be added as soon as the coloured dot in the lid on the salt container 27 is no longer visible. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. Filling the rinse-aid container The purpose of a rinse-aid is to prevent the formation of water marks on tableware and utensils, and to ensure that glasses are clean and sparkling. The rinse-aid is consumed during the washing process. Fold back the lid on the rinse-aid container 30 . To open the lid, press the mark (1 ) on the rinse-aid lid and simultaneously lift the lid off the lug (2 ). 1 2 Pour the rinse-aid into the filler hole until the level indicator turns dark. Close the lid, ensuring that you hear it snap closed. Use only rinse aid for domestic dishwashers. Spilt rinse aid may result in excessive foam formation in the next rinse cycle. Therefore, remove any spilt rinse aid with a cloth. en Adjusting the amount of rinse-aid The amount of rinse-aid added to the water can be varied by adjusting the stepless control. The rinse-aid control has been set to ”4” in the factory. Do not alter the setting of the rinse-aid control unless streaks (turn knob towards ”–”) or water marks (turn knob towards ”+”) are left on the...

Эта инструкция также подходит к моделям:
Посудомоечные машины - CG341J2/22 (2.45 mb)
Посудомоечные машины - CG341J2/23 (2.45 mb)
Посудомоечные машины - CG341J2/25 (2.45 mb)
Посудомоечные машины - CG341J5/21 (2.45 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории