Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Press pads for desired cycle and options. i Ul,, ii,,,,ll In addition to showing remaining delay or cycle time, the digital display will show a code indicating the dishwasher's condition: ° PF will appear in the display the first time the dishwasher is connected to the elec trical supply after inetallation_ This display also indicates there was a power failure. Press Cancel/Drain to drain the dishwasher. If there is no water in the dishwasher, press Cancel/Drain a second time, Reselect a cycle to restart the dishwasher. Sani Complete The Sani Complete light glows at the end of the cycle indicating a high temperature, sanitary rinse was completed° NOTE: A flashing Sani Complete light indicates that a high temperature, sanitary rinse was not completed, The Sani Complete light will flash at the end of the cycle if the dishwasher door is opened, power fails, or water heating is not completed during the final rinse. You may need to turn your water heater temperature up so water is at least 120°F (49°C) as it enters the dishwasher. 4_ The display will show the number of hours remaining until washing begins. The display will show hours only: If the display shows 2, there is between 1 hour and 1 hour 59 minutes remaining., & When the hours of delay you have set have elapsed, the dishwasher will start the cycle selected in Step 3oThe wash time wi!l count down the minutes remaining in the cycle to O. If you wish to put more dishes in the dishwasher while it is in the delay mode, be sure to latch the door after adding them The timer wil! not advance unless the door is latched. To cancel Delay Wash, press the CanceVDrain pad. ° CC will appear on the display when the dishes are washed and the cycle completed, Opening the door or pressing the Cancel/Drain pad wifl dear the display. E2 witl appear in the display if the selector pads are stuck. Press CanceVDrain to release the controls, or run your fingers across the pads to free them up. If E2 remains in the display, call for service. Your Part ° Cleaning Operating your dishwasher properly enables you to obtain the best possible results, proper dishwasher operation,, o Use automatic dishwashing detergent only, Other detergents are too mild and much too sudsy. o Add detergent just before starting cycle. ° Store tightly closed detergent in a cool, dry place. Fresh automatic dishwasher detergent results in better cleaning. Filling the detergent dispenser Cover The detergent dispenser has one section with a cover and one withouL Push cover down firmly until it latches. Detergent in the open section fails into the dishwasher when closing the door The covered section opens automatically for the main wash HOTE: It is normal for cover to open partially when dispensing detergent. Use only covered section for cycles with one wash How much detergent to use o The amount of detergent to use depends on the WATER TYPE hardness of your water and the type of detergent If you use too little, dishes won't be clean° If you Hard use too much in soft water, glassware wilt etch, 8+ grains per gallon o Different brands of dishwasher detergent have 136+ parts per million different amounts of phosphorus for softening water. ]f you have hard water and use a detergent Medium with a phosphorous content of less than 8.7%, 5-7 grains per gallon you may need to use more detergent, or use a 85-119 parts per million detergent with a phosphorous content higher than 8_7%. Soft o Find out your water's hardness by asking your 0-4 grains per gallon local water department or water softener company. 0-68 parts per million NOTE: Fill amounts shown are for standard powdered detergent, Amounts may vary if you use liquid or concentrated powdered detergent,. Follow manufacturer's directions when using liquid dishwasher detergent or concentrated powdered detergent. This section explains Cover latch Use both sections for cycles with two washes WHERE TO FILL Top of 3rd step (3tbs ) Top of 2nd step (2 tbs.) Top of I st step (1 tbs.) Keep the rinse agent dispenser filled with a liquid rinse agent. A rinse agent greatly improves dish drying by helping water flow off them during the last rinse, A rinse agent also keeps water from forming droplets and drying as spots or streaks° To check dispenser: o Check center of fill indicator cap. Clear means it needs filling, A small amount of rinse agent automatically releases into the rinse water during the final rinse of each cycle. For best drying results, check dispenser periodically to see if it needs filling. o Or remove fill indicator cap. An "E" is visible at the bottom of the dispenser when empty, To fill dispenser; The rinse agent dispenser holds 6 ounces (! 75 mL), Under normal conditions, this lasts about 3 months. 1. Open dishwasher door completely 2. Remove fill indicator cap1 3. Add rinse agent° Fill to smallest opening in lower part of dispenser only Overfilling may cause rinse agent to leak out., This will not harm the dishwasher, but could cause oversudsing 4. Clean ...
Эта инструкция также подходит к моделям:Посудомоечные машины - 15821 (2.67 mb)
Посудомоечные машины - 15828 (2.67 mb)