Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Upper arm nozzles point downward, and lower arm nozzles point upward. Arms in the prewash chamber each have two tubes (the slightly longer arm goes below). The arms with five tubes fit in the upper brackets, and the arms with four tubes fit in the lower brackets. To install arms, slide manifolds on the guides toward the rear of the machine (Fig. 26). Then latch arms in place (Fig. 27). Fig. 25 Fig. 26 Fig. 27 Replace the pump intake screens, strainer pans, and strainer baskets. Rehang the curtains (refer to pages 11 – 14). Leave the machine doors open to allow the interior to air out and dry. Clean machine exterior like any other stainless steel appliance. Use damp cloth and mild soapy water. Flush the openings where the sensors are located at the load end of the machine (Fig. 28). Do not attempt to clean these openings with any metallic object as damage to sensors can occur. CLEAN SENSOR OPENINGS AT LOAD END OF MACHINE Fig. 28 – 8 – CLEANING THE TOP DUCT Disconnect electrical power supply(ies) and follow lockout / tagout procedures before you begin cleaning. Debris and airborne particles will settle on the Top Covers and the surfaces inside the Top Duct. The Top Duct should be cleaned about every two weeks, as appropriate for your location. There are two handles on each of the removable Top Covers so they can be lifted or moved to access the inside of the Top Duct for cleaning (Fig. 29). Before draining and cleaning the machine, perform the following cleaning task. Use an appropriate ladder and both hands to remove each Top Cover. Clean inside the Top Duct with mild detergent / warm water solution and brush, cloth, or sponge. Clean the Top Duct from the UNLOADENDof the machine towards the LOADEND. If necessary, the Top Duct may be hosed down. Rinse with clean water. Clean both sides of the Top Covers individually while they are removed. After cleaning the Top Duct and the Top Covers, replace each Top Cover in its correct location. After cleaning the Top Duct, clean the dishwasher as discussed on pages 7 – 8. TOP DUCT TOP COVER REMOVED BOTTOM OF DUCT Fig. 29 – 9 – CLEANING THE BLOWER-DRYER AIR FILTER At least twice each month, the air filter (when present, Fig. 30) on the blower-dryer should be removed and cleaned in a sink with warm soapy water and hosed off with clean water. The air filter can be washed in the dishwasher and flushed with clean water after washing. Replacement air filters are available — contact Hobart service. DOs AND DON'Ts FOR YOUR NEW HOBART DISHWASHER DO assure proper water hardness of 3 grains or less per gallon. DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave doors open). DO closely follow your chemical professional's prescribed deliming schedule. DO use only products formulated to be safe on stainless steel. DO NOT over soften water (recommended water hardness range is 3 grains or less per gallon). DO NOT use detergents formulated for residential dishwashers. DO NOT allow food soil to accumulate on the tank bottom. DO NOT exceed chemical manufacturer's recommended concentrations for detergent, rinse aid, or lime scale remover. DO NOT use steel wool to clean ware or dishwasher surface. DO NOT allow foreign objects to enter the unit, especially metallic contaminants. NOTE: Failure to follow use, care, and maintenance instructions may void your Hobart dishwasher warranty. BLOWER-DRYER FILTER LIFT UP AND PULL FORWARD TO REMOVE R – L OPERATION SHOWNFig. 30 – 10 – CURTAINS AND DRAINBACK PANS, MODEL FT900 Curtains and drainback pans must be in their proper places, Fig. 31 . . . • Hang a short curtain on the unload side of each upper prewash, wash and power rinse arm. • Hang a long curtain on both sides of every section joint. • Hang two long curtains at the load end. • Hang one long curtain at the unload end. • Drainback pan locations are shown for reference only. FINAL RINSE ARM POWER RINSE ARM WASH ARM PREWASH ARM FT900 R TO L OPERATION 8' CENTER SECTION THREE SHORT CURTAINS AT UNLOAD SIDE OF UPPER ARMS FOUR PAIRS OF ONE LONG CURTAIN LONG CURTAINS AT UNLOAD END LOAD UNLOAD FINAL RINSE DRAINBACK PAN STRAINER PREWASH ARM WASH ARM POWER RINSE ARM FINAL RINSE ARM FT900 L TO R OPERATION 8' CENTER SECTION THREE SHORT CURTAINS AT UNLOAD SIDE FOUR PAIRS OF OF UPPER ARMS LONG CURTAINS ONE LONG CURTAIN AT UNLOAD END UNLOAD STRAINER TWO LONG & THREE SHORT DRAINBACK PANS TWO LONG & THREE SHORT DRAINBACK PANS LOAD FINAL RINSE DRAINBACK PAN Fig. 31 – 11 – CURTAINS AND DRAINBACK PANS, MODEL FT900D Curtains and drainback pans must be in their proper places, Fig. 32 . . . • Hang a short curtain at the unload side of every upper prewash, wash, power rinse and dual rinse arm. • If equipped with a blower-dryer, hang another short curtain after the final rinse arm. • Hang a long curtain on both sides of the prewash / wash section joint and the wash / power rinse section joint. • ...
Эта инструкция также подходит к моделям:Посудомоечные машины - FT900 (2.69 mb)
Посудомоечные машины - FT900D (2.69 mb)