Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Start the machine momentarily and verify proper direction of rotation. Electric Heat Connect a permanent electrical power supply to the line terminals of the control box. The tank water temperature is regulated by a solid-state thermostat which is preset at the factory and should not require adjustment. If an adjustment is necessary or the machine is to operate low temperature, contact your local Hobart service office. Use the machine thermometers for verification of proper water temperatures. – 17 – ELECTRICAL CONNECTIONS — OPTIONAL EQUIPMENT ELECTRICAL CONNECTIONS — OPTIONAL EQUIPMENT WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. OPTIONAL EQUIPMENT CONTROL CONNECTIONS Detergent Dispenser Maximum rating for detergent dispenser connected to DPS1 and DPS2 is 1.5 Amps at line voltage. Rinse Aid Dispenser Maximum rating for rinse aid dispenser connected to RPS1 and RPS2 is 1.5 Amps at line voltage. Vent Fan Control Maximum rating for vent fan control connected to VFC1 and VFC2 is 1.5 Amps, pilot duty. – 18 – CURTAIN INSTALLATION – 19 – OPERATION PREPARATION Put the dishwasher strainer pans and strainer basket (Fig. 3) into position in each dishwasher tank. If the machine is equipped with an RS, CS, or PW unit, install the solid prewash strainer pan over the overflow tube, flange side down and the lip toward the rear of the tank. Install one perforated strainer pan, handle side up, across the rear of the tank. Install the other perforated strainer pan against the load end of the tank and locate the flange into the notches on the solid and perforated strainer pans. Drop in the perforated strainer basket (Fig. 11). Fig. 11 Fig. 12 Hang curtains on open hooks provided. Refer to Curtain Installation. Move drain lever(s) down to close the drain(s) (Fig. 12), or close the door(s) to automatically push the lever(s) down. FILLING THE DISHWASHER Water must be proper hardness. Recommended hardness range is 4 to 6 grains/gallon. Turn the Power switch ON (Fig. 1). Leave pumps OFF until machine has completely filled. If the machine is equipped with an RS, CS or PW unit, the prewash tank will fill last, with overflow water from the wash tank. If the machine is equipped with steam heat, the mechanical ball valve (located between the drive motor and the tank) must be opened by pulling the valve lever down. – 20 – If the machine is equipped with gas heat, refer to STARTING THE GAS HEAT DISHWASHER below. If the machine is equipped with gas heat, refer to STARTING THE GAS HEAT DISHWASHER below. Minimum temperatures for all models are: Single-Tank Models WASH TANK RINSE TANK FINAL RINSE C44A/AW, C54A 160°F (Min.) –––– CRS66A/AW, CRS76A CPW80A/AW, CPW90A CCS66A/AW, CCS76A 180°F (Min.) Two-Tank Models C64A, CRS86A, CCS86A, 150°F (Min.) 160°F (Min.) CPW100A, C88A, CRS110A, CCS110A, CPW124A 180°F (Min.) Minimum temperatures for optional low-temperature operation are: Wash Tank -140°F Rinse Tank -140°F ...
Эта инструкция также подходит к моделям:Посудомоечные машины - C44AW ML-104083 (1.56 mb)
Посудомоечные машины - C44A ML-104047 (1.56 mb)
Посудомоечные машины - C44A ML-104050 (1.56 mb)
Посудомоечные машины - C44A ML-38898 (1.56 mb)