Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Step 4: Select wash programme as normal. Please Note: If the above does not solve the problem, check that the water feed pipe filter is not blocked. “END” will flash in the display at one-second intervals to indicate the programme is complete & the machine is in standby mode. -Press & hold the “On/Off” button to switch off the dishwasher. Please Note: When your dishwasher is switched back on, “END” will continue to flash in the display until a new programme is selected – This is normal. Fault Area Issue Messages In The Display -DEMO Lit in Display - Demonstration mode actived On/off Button Start/Reset Button -AL05 in Display -Possible Filter Blockage On/off Button Cause/How to resolve… “Demo” will slide across the display when the Demonstration mode has been accidentally activated. Follow the instructions below to cancel “Demo” mode: Step 1: Press & hold simultaneously the “On/Off button” and “Start/Reset button”, until “D of” is illuminated in the display. Step 2: Select wash programme as normal -If AL05 is illuminated in the display, then you need to clear the filter of any blockages before programme can proceed. Step 1: Press & hold the “On/Off button”, until 4 dashes are illuminated in the display. Step 2: Remove filter from base of machine. Step 3: Rinse filters under running water and ensure that large food particles are removed from Area A. Step 4: Locate filters back into the filter housing and firmly press downwards. Step 5: Turn the dishwasher on by pressing the “On/Off” button, and select required programme. 1 2 AB C Poor Wash Results Residue On Dishes When Wash Cycle Complete For additional advice on Cleaning your filter see “Care and Cleaning” section of the instruction book. -Is the selected programme suitable for the type of load and the degree of soiling? -Check the loading of your crockery into the baskets (See “Loading You Dishwasher” Section of the instruction book). -Check that the filters are clean and in place (See “Care and Cleaning” Section of the instruction book. -Is the lid of the salt container closed properly? -Is the rinse aid dosage correct? (See section “Poor Drying Results” below for instructions on adding or adjusting rinse aid to your wash). Fault Area Issue Cause/How to resolve… Poor Wash Results Tablet not dissolving - Wherever possible the following should be positioned away from dispenser, to ensure that they can not come into contact with the Dispenser - Cutlery / Cutlery Basket - Crockery - Casseroles Dishes/Pans Etc Spray arm Obstruction Upper BasketUpper Spry ArmSpry wash jetholes-Prior to starting the programme ensure the spray wash jet holes are not blocked and also that the spray arms can rotate freely. 26 cm. 26 cm. With the upper basket in the lower position, the maximum height for plates is 26cm. 21cm. 31 cm. With the upper basket in the upper position, the maximum height for plates is increased to 31cm. To adjust the upper basket position, follow instructions below: -To adjust the height setting of your upper basket move handles up or down and then push in until you hear it clip into position (See Fig 1):· Handle points downwards when upper basket set to lower position (See Fig.2). -Handle points upwards when upper basket set to upper position (See Fig.3). Fig.2 Fig.1 Fig.3 Fault Area Issue Cause/How to resolve… Poor Drying Results Quick Wash Programme -There is no drying cycle on the Quick Wash Programme, unless you have selected the “Extra Dry” option. Selected Follow instructions below on how to select “Extra Dry” Step 1: Press button marked “M” until the “Extra Dry” cycle indicator is highlighted & “OFF” is illuminated in the display. Step 2: Activate the “Extra Dry” option by pressing the button marked “S” until “ON” is illuminated in display. Pre-Wash Programme Selected -There is no drying cycle on the Pre-Wash Programme. Is Rinse Aid being used or is the -Using rinse aid in your wash will improve the drying performance. Rinse Aid level set too low? To add rinse aid to your wash follow instructions below: Step 1: Rotate cap anti-clockwise and pull to remove. Step 2: Pour rinse aid into container and secure cap back into position. Cap The level of rinse aid used during your wash cycle can be adjusted to ensure best results. Rinse Aid Levels 1 (lowest) to 6 (Highest) Rinse Aid level adjuster is located under dispenser cap. Using small coin rotate adjuster to desired setting. (We recommend setting to 4). Rinse Aid Adjuster D ISHWASHE. Fault Area Poor Drying Results The Dishwasher Will Not Drain General Issue Possible Installation Fault (Particularly if the machine is being used for the first time) Unusual Amount of foam is created Dishwasher Stopping During Cycle Knocking Noise coming from Dishwasher Knocking Noise Coming from Inlet Valves Cause/How to resolve… -Check -Is the drain hose kinked? -Is the sink trap blocked? (If this is the case you will experience problems with your sink drainage). -Ensure the blanking plug/closed end connection has been rem...