Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
. In order to ensure that the correct amount of salt is being used to regenerate the water softener, the dishwasher is equipped with an electronic device for adjusting the water softening setting. The setting may be adjusted electronically. To set this correctly the hardness of your water needs to be ascertained. SETTING WATER HARDNESS N. 1 NO SALT N. 1 N. 2 N. 3 N. 4 N. 5 0 - 4°dH (0 - 7°dF) 5 - 9°dH (8 - 15°dF) 10 - 22°dH (16 - 37°dF) 23 - 29°dH (38 - 50°dF) 30 - 35°dH (51 - 60°dF) 36 - 41°dH (61 - 70°dF) WATER HARDNESS TABLE: . Contact your local water board for information on the water hardness for your area. When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 wash cycles. The salt container can hold approximately 1.7Kg of salt in grains. FILLING THE SPECIAL SALT CONTAINER... Note: Only use recommended Dishwasher salt or granular salt. DO NOT use everyday table salt, cooking salt or road salt as they contain insoluble substances which could harm the Dishwasher. How the salt works: While washing is taking place, salt is automatically rinsed out of the salt container into the water softener where it dissolves the lime in the water. The dissolved lime is pumped out of the dishwasher. The water softener system is then ready for the next load. This process of regeneration can only function when the salt is dissolved in water. The container is situated at the bottom of the dishwasher. You will need to remove the lower basket for access. . You should fill just before starting the programme. . Unscrew the lid of the salt container, turning it anti-clockwise to remove. Before using the dishwasher for the first time, pour approximately 1 litre of water into the salt container. . Use the supplied funnel to fill salt to the top of the container. As you tip in the salt some of the water is displaced and drains away. When you have done this, clean off any remnants of salt from the area around the neck of the container. Always make sure that the cap is replaced securely ensuring that it is not cross-threaded. Information: Add salt when required as advised in the chart on the previous page. Refill the salt container before starting the wash programme. In this way the excess saline solution will be immediately washed away by the water, the prolonged presence of salt water inside the tank may lead to corrosion. When using the dishwasher for the first time, in addition to the salt it is also necessary to add ONE litre of water to the container. WARNING: DO NOT pour detergent into the special Salt Container. This will destroy the water softener. Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the guarantee will be invalidated. The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left and the rinse aid dispenser is on the right. FILLING THE RINSE AID CONTAINER... The purpose of Rinse Aid is to help the dishes dry faster and to prevent formation of water marks on tableware and utensils, and to ensure that glasses are clean and sparkling. Rinse Aid is consumed during the washing process and needs adding when required. RINSE AID WARNING LIGHT (Model DF56) -Open the door. Rotate the rinse aid container cap anticlockwise by 1/4 of a turn and remove it. -Add the rinse aid until the container is full (approximately 140cc). The level indicator on the side should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates (Model DF56 only). -Replace the cap, turn clockwise and ensure it is securely closed. -Use a cloth to remove any spillage. Important: Only use rinse aids intended for use in domestic dishwasher's, Adjusting the amount of Rinse Aid... The amount of rinse aid added to the water can be varied by adjusting the control. The rinse aid control has been factory set for medium water hardness. Do not alter the setting of the rinse aid control unless streaks or water marks are left on the dishes. To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anti-clockwise direction and remove it. Use a screwdriver to turn the rinse aid control to the required position. Replace the cap securely turning clockwise. RINSE AID CONTROL . The amount of rinse aid needs to be increased if the appear dull or you can see circular stains. . The amount of rinse aid needs to be reduced if the dishes are sticky or you can see whit streaks. DETERGENTS... Information about detergents: You can use any brand of liquid or powder detergent, as well as tablets, that have specifically designed for use in domestic dishwasher's. DO NOT use normal washing up liquid. There are three types of dishwasher detergent a...
Эта инструкция также подходит к моделям:Посудомоечные машины - DF56 (2.29 mb)