Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
. This will prevent the pipe from jumping out during installation and use. DO NOT position the standpipe near an electrical outlet. ENSURE that the drain hose is not kinked and it is routed as shown in the diagram. The standpipe should have a bore of at least 38mm (11/2”). It should be installed as shown, have a trap fitted and must discharge into the same drain system as your household sink. It MUST NOT be connected to a surface water drain. Sink Waste System: For under sink drainage: Before connecting the drain hose, remove any internal restrictions This will prevent a build up of debris which could cause a blockage. Remove any restrictions from the waste spigot and ensure that the sealing bung is removed. The hose should be routed, such that it is raised to a minimum height of 800mm (31/2”). NOTE: Ensure the sink outlet pipe has a minimum diamtere of 32mm. 1. Untie the end of the GREY drainage hose from the rear of the appliance. 2. Reposition the ‘Hooked End Support’ as required along the GREY drainage hose. 3. If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug. 4. Attach the GREY drainage hose to the under sink waste disposal unit securely, using the clip and rubber tube supplied. Ensure the drain hose is securely attached, to prevent it coming away while the machine is in use and causing a flood. D ISHWASHER Getting to know your Dishwasher E. Upper basket F. Top spray arm G. Basket height adjuster H. Lower basket The Controls A. ON-OFF Button Press this button to switch the appliance on. B. ON-OFF Indicator light This light informs you that the dishwasher is on. C. Door opening handle Use this handle to open the door. D. Delayed start select button This button delays the start of the wash cycle you selected by 12, 9, 6 or 3 hours. E. Cycle indicator light This light informs you which cycle you have selected or the one in progress. F. Half load selection button To allow you to wash a half load in the upper basket. I. Bottom spray arm J. Salt container cap K. Washing filter L. Detergent and rinse aid dispenser G. Cycle phase and delayed startindicator lights Thes indicator lights inform you which cycle phase is underway (prewash,wash,rinses,drying). If you have set a delayed start, they also indicate the amount of time left until the wash cycle starts. H. Half load indicator light This light informs you that the half load is selected. S EF T P P. Cycle select button Each time this button is pressed, one of the cycle indicator lights “E” will come on in sequence. R. Start / Reset button With Start the wash cycle begins, whereas a;; the settings are cleared with Reset. R H C S. Low Salt indicator light This light warns you that it is time to add more salt. T. Low Rinse Aid indicator light This light warns you that it is time to add more rinse aid. GA B D This dishwasher conforms to the following European Community Directives: • 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; • 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications; Technical Characteristics Width 60cm Depth 60cm Height 85cm Capacity up to 14 place settings Mains Water Pressure 10 bar)1MPa (0,330 KPa Power Voltage see rating plate Total absorber power see rating plate Fuse see rating plate D ISHWASHER How to use your Dishwasher First of all. -Turn on the water supply tap completely. -Add the correct amount of detergent. -Load the baskets correctly. -Check that the spray arms rotate freely. -Close the door securely. -Press the ON-OFF button "A": you will hear a short beep and indicator light "B" comes on. Your appliance is now on and awaiting instructions. Select the wash cycle. Select the wash cycle by pressing button "P". Each time this button is pressed, a beep will sound and indicator lights “E” will come on in sequence.Select the wash cycle most suitable for the type of dishes to wash (see ‘Programme Chart’). Close the door and press the Start button after a few seconds, you will hear a short beep and the wash cycle will started. The dishwasher informs you. Your dishwasher has indicator lights "G" which light up to indicate the wash cycle phase that is underway. Modifying a wash cycle in progress. If you have chosen the wrong cycle -You can modify the wash cycle in progress, if it has only just started. Keep the Reset button "R" pressed in for approximately 5 seconds, a prolonged beep will sound, followed by three short beeps. Indicator light "G" will go out to show all the settings will have been cancelled. You are now free to re-set the correct wash cycle. You've left out a dish? Interrupt the wash cycle by pressing the On-Off button "A", then insert the dish you had forgotten. When you shut the door, press the On-Off button again. The cycle will start up from where you interrupted it. Cycle end The end of the wash cycle is indicated by 2 short beeps and the flashing of the drying phase indicator light. Turn the appliance off by pressing the On-Off ...
Эта инструкция также подходит к моделям:Посудомоечные машины - DWF50 (2.35 mb)