Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
DishDrawer® must be securely anchored before it is operated. AwARNING! Before installing the DishDrawer®, remove the house fuse or open the circuit breaker. Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations. Important! These instructions must be followed precisely to ensure correct venting and operation of the DishDrawer®. In the event of a fault related to the incorrect installation, the installer will be liable for any repairs. Important! The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is required. Important! Improper installation is not covered under the Warranty. Important! If the DishDrawer® is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage. BEFORE YOU START - DOUBLE & SINGLE MODELS PARTS SUPPLIED DOUBLE MODELS DishDrawer Flexible Extrusion for Sides (2) Edge Protector (!) Flexible Extrusion for Top (!) Installation Tabs (2) Clamp (1) Drain Hose Support (!) Drain Hose Joiner (!) © Washer (1) &=?' Wire Clips (2) Phillips 16mm Screws (7) Moisture Protection Tape (!) p/n 527208 Prefinished Toe Kick (1) White prefinished toe kick kit p/n 526678 or Black prefinished toe kick kit p/n 526679 or Iridium prefinished toe kick kit p/n 527109 fOGLSNEEDEn Wooden Chopping Board Tape Measure Spirit Level Safety Glasses Utility Knife Pencil Sandpaper Drill & No.2 Phillips Bit No.2 Phillips Screwdriver Flat Screwdriver Adjustable Wrench or M5 Socket 01'/2" (38mm) Hole Saw Side Cutting Pliers SPARE PARTS INSTALLATION KIT FOR SINGLE & DOUBLE MODELS: p/n 526676 INSTALLATION PREPARATION ELECTRICAL PREPARATION A) The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after installation. B) The switched power outlet must be between 6" (150mm) and 18" (450mm) from the DishDrawer® cavity. C) Refer to Page 9, Step 5 for electrical connection options. Important! The services hole in the DishDrawer® cavity needs to be large enough for the plug on the power supply cord to fit through, but MUST NOT be more than 1V2" (38mm). PLUMBING & DRAINAGE PREPARATION A readily accessible valve must be installed in the water supply pipe. If the supply pressure exceeds 145 psi (1000kPa), then a pressure limiting valve must be used. Review Plumbing Options on pages 4 & 6. Choose a method that best suits your needs. A Drain Hose extension Kit P/N 525798 will extend the drain hoses by 1413/4" (3.6m). The kit is available from the nearest Fisher&Paykel Authorized Service Agent. DO NOT extend beyond this limit. This Dishwasher's maximum drain height is 371/2" (950mm). A) B) C) D) E) CAVITY PREPARATION A) It is recommended that all cabinetry surrounding the DishDrawer® (including the underside of the countertop) is sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam damage. The air in the cavity can get very hot and humid (saturated at 122oF/50oC) B) The self-adhesive moisture protection tape must be applied to the underside of the countertop to prevent moisture damage, (refer to cavity diagram pg 3 or 5). Be sure surfaces are dry and dust-free prior to application. C) Be sure the cavity provides sufficient material to secure the DishDrawer® using the mounting tabs (refer to step 1, page 7). If there is nothing to screw to, add a brace. See page 3 or 5 for screw locations. D) The services hole MUST be immediately adjacent to the rear lower corner of the cabinetry. If not, the hoses will prevent the DishDrawer® being pushed back into the cavity all the way. The hole can be located on either side depending on the location of the services. E) Be sure the cavity sides are plumb (vertical) as this will assist with levelling the DishDrawer® . F) Minimum clearances: 1/s" (2.5mm) V2" (13mm) ELECTRICAL INFORMATION POWER SUPPLY CORD A) Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord. B) If the power supply cord is damaged, it must be replaced by the Manufacturer, Service Agent or a similarly qualified person in order to avoid a hazard. GROUNDING INSTRUCTIONS A) This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. AwARNING! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. B) This appliance is equipped with a power supply cord having an equipment-grounding conductor and an earthing plug. The power supply plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local ...