Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Factory setting: on. You can deactivate the acoustic signals. Deactivating the acoustic signals 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indicators of touchpads (3), (4), (5) and (6) flash. 4. Press touchpad (5), • The indicators of touchpads (3), (4) and (6) go off. • The indicator of touchpad (5) continues to flash. • The display shows the setting of the acoustic signals. On Off ENGLISH 11 5. Press touchpad (5) to change the setting 6. Deactivate the appliance to confirm. SETTING THE TIME BEAM COLOUR Nine colours are available for this light beam. You can change the colour or deactivate it. 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indicators of touchpads (3), (4), (5) and (6) flash. 4. Press touchpad (6). • The indicators of touchpads (3), (4) and (5) go off. • The indicator of touchpad (6) continues to flash. • The display shows a number and the letter C. Each number is related to a different colour (0C = Time Beam deactivated). 5. Press touchpad (6) again and again to change the colour. 6. Deactivate the appliance to confirm. BEFORE FIRST USE 1. Make sure that the set level of the water softener agrees with the water hardness in your area. If not, adjust the water softener. Contact your local water authority to know the water hardness in your area. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Processing residues can stay in the appliance. Start a programme to remove them. Do not use detergent and do not load the baskets. If you use the combi detergent tablets, activate the multitab function. These tablets contain detergent, rinse aid and other added agents. Be sure that these tablets are applicable to the water hardness in your area. Refer to the instructions on the packaging of the products. ADJUSTING THE WATER SOFTENER Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water softener neutralises these minerals. The dishwasher salt keeps the water softener clean and in good conditions. Refer to the table to adjust the water softener to the right level. It makes sure that the water softener uses the correct quantity of dishwasher salt and water. You must adjust the water softener manually and electronically. Water hardness Water softener adjustment German French mmol/l Clarke Manual Elecdegrees degrees degrees tronic (°dH) (°fH) 51 - 70 91 -125 9.1 - 12.5 64 -88 2 1) 10 43 - 50 76 - 90 7.6 - 9.0 53 -63 2 1) 9 37 - 42 65 - 75 6.5 - 7.5 46 -52 21) 8 29 - 36 51 - 64 5.1 - 6.4 36 -45 21) 7 23 - 28 40 - 50 4.0 - 5.0 28 -35 21) 6 19 - 22 33 - 39 3.3 - 3.9 23 -27 21) 51) 15 - 18 26 - 32 2.6 - 3.2 18 -22 1 4 11 - 14 19 - 25 1.9 - 2.5 13 -17 1 3 4 -10 7 - 18 0.7 - 1.8 5 - 12 1 2 < 4 < 7 < 0.7 < 5 12) 12) 1) Factory position. 2) Do not use salt at this level. ENGLISH 13 Manual adjustment Turn the water hardness dial to the position 1 or 2. Electronic adjustment 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indicators of touchpads (3), (4), (5) and (6) flash. 4. Press touchpad (3). • The indicators of touchpads (4), (5) and (6) go off. FILLING THE SALT CONTAINER • The indicator of touchpad (3) continues to flash. • The acoustic signals operate. Example: five intermittent acoustic signals = level 5. • The display shows the setting of the water softener. Example: = level 5. 5. Press touchpad (3) again and again to change the setting. 6. Deactivate the appliance to confirm. CAUTION! Only use dishwasher salt. Other products can cause damage to the appliance. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme. 1. Turn the cap counterclockwise and open the salt container. 2. Put 1 litre of water in the salt container (only for the first time). 3. Fill the salt container with dishwasher salt. 4. Remove the salt around the opening of the salt container. 5. Turn the cap clockwise to close the salt container. FILLING THE RINSE AID DISPENSER MAX1234+- ABDC1. 2. CAUTION! Only use rinse aid for dishwashers. Other products can cause damage to the appliance. The rinse aid, during the last rinsing phase, helps to dry the dishes without streaks and stains. Press the release button (D) to open the lid (C). Fill the rinse aid dispenser (A), no more than the mark 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks ...